What Is EpoxyShield, and Is It Really Worth The Extra Cost?


If you’re looking to make your garage floor look like it’s new, epoxyshield may be the answer. The product claims to offer a durable and long-lasting finish that requires little prep work for DIYers. It’s easy to use and provides a smooth finish with minimal dry time. Let’s take a closer look at what makes this product so special, how well it performs in real-life situations, and if it truly is worth the extra cost over regular paint products.

Epoxyshield is a specialized formula of resin-based coatings that is marketed as an easy-to-use product for DIYers

EpoxyShield is a specialized formula of resin-based coatings that is marketed as an easy-to-use product for DIYers. It differs from other flooring paints in several ways, including the fact that it contains no solvents and emits zero fumes during application; this makes it ideal for indoor applications like garages and basements. Epoxyshield also offers superior protection against chemicals, oil, grease, and other contaminants because of its unique dual-cure system. The first cure takes place immediately after application; this allows the surface to be walked on immediately after application without damaging the finish or leaving dirt behind. After 24 hours of dry time has passed (or longer depending on temperature), a second hardening occurs which creates an extremely durable coating resistant to scratches, chips, and scuffs.


What does epoxyshield do?

EpoxyShield is a specialized formula of resin-based coatings that are marketed as an easy-to-use product for DIYers. It creates a fluid-proof, chemical and stain-resistant surface that will last for several years.

The epoxy coating comes in two different products:

  • EpoxyShield Waterborne Coating (WBC) – This is the most popular product on the market today. It’s made from an advanced resin technology that provides high solids content for maximum durability and protection against water penetration, chemicals, and stains. The WBC has been tested by third parties to be able to withstand damage from chemicals such as gasoline or diesel fuel spills up to 5 minutes after direct contact with these liquids!

Pros and Cons to consider when it comes to this product

While epoxyshield does provide a smooth finish and fairly good durability, there are other pros and cons to consider when it comes to this product.

  • The finish is not consistent. Some users report that their final product was not as smooth as they would have liked it to be, but others say that the epoxy appears perfectly smooth after drying.
  • It can be expensive for what you get in return. While an 8-ounce bottle costs about $20 on average, you will only get about 4-6 square feet of coverage from each bottle, so if you’re planning on doing any more than one small project—or even just one big project—you will likely need more than one bottle of epoxy shield for your job.

Overall, though, EpoxyShield is a good product with some faults that make it less ideal than other options out there. If you don’t mind spending extra cash or having inconsistent results with your finished projects then go ahead and give EpoxyShield a try!

Oil-based versus water-based

After you’ve decided on the type of EpoxyShield coating you want to apply, you’ll need to decide what kind of finish you’re going for. There are two kinds: oil-based and water-based.

Oil-based finishes are more durable than water-based finishes. If you’re looking for something that will last longer and protect your car from scratches, this might be a good choice for you. Oil-based EpoxyShield comes with a dry film thickness of 1/8″ (3mm) to 1/4″ (6mm). A thinner coating means less material is required to cover large surfaces, which means using less money in the long run—but it also means that your paint job won’t look as smooth or mirror-like as it would with a thicker application.

Water-based EpoxyShield is easier to work with because it’s easier to spread around and clean up afterward (you can use soap and water). However, because there’s less material being applied, its lifespan won’t be as long—and there’s no way around this fact: any time something has been applied over your car’s existing coatings (be they polyurethane or not), there’s always some level of risk involved!

Prep is the key to a shiny paint job

The first step is to clean your floor with a degreaser that is safe for your flooring. It’s also important not to leave any residue from the cleaner on your floor after it dries, so make sure you use plenty of water to rinse off any remaining soap or chemicals before applying EpoxyShield.

After cleaning, use a brush to scrub the floor with Amway Cleaning Solution in order to remove dirt, grime and grease from floors so they’re ready for coating. This can be done by hand or using an electric scrubber on low setting (the lowest speed). If you have access to one, it will speed up this process but isn’t necessary since we only recommend doing this once per year anyway!


Epoxyshield costs twice as much as regular flooring paint.

Epoxyshield is a specialty coating that costs twice as much as regular flooring paint, but it’s worth it. A gallon of Epoxyshield will run you $70 to $80, while you can get an entire gallon of regular paint for around $30 to $35.

That might seem like a lot more money at first glance, but once you think about all the work involved in applying epoxy versus simply painting over your existing floor with paint, it becomes clear that Epoxyshield is actually cheaper than regular flooring paint.

In addition to its affordable price tag, what makes Epoxyshield such a worthwhile investment for most DIYers is its versatility and durability. You can use this product on any kind of bare concrete surface—including garage floors and basements—as long as it hasn’t been sealed previously with another type of coating (like polyurethane).


One gallon covers approximately 250 square feet

One gallon covers approximately 250 square feet. This can vary depending on the porosity of the wood and any existing finish, but in general, you expect to cover roughly 250 square feet with a single gallon of EpoxyShield. The more coats, the longer they will last.

So how many coats do you really need? That depends on what type of project you’re doing and what level of protection you want from moisture and dirt penetration! For example:

You want to seal over an existing finish without adding fire retardant properties*: Apply one coat after sanding down your existing finish with 220 grit paper. Let dry completely before applying another layer (you may also want to allow some time for curing between coats). Repeat until desired coverage is achieved – two or three coats should be sufficient for most projects like this!

If this is an outdoor project where water exposure is likely: Apply two coats after sanding down your existing finish with 220 grit paper – at least 24 hours apart from each other (one hour if possible) so that each coat has time set before applying another layer.

The coating must be applied in dry temperatures between 60 to 90 degrees

The epoxy coating should be applied in dry temperatures between 60 to 90 degrees. This is the temperature range that will ensure a good bond and will keep the roof looking its best. If the temperature is too warm or too cold, the coating could lose its adhesion and flake off prematurely.

Additionally, you’ll need to allow 3 days for your roof to dry before applying any additional coats of EpoxyShield. Many people wait longer than 3 days because they’re worried about re-wetting their roofs or getting them wet by mistake after application—but this isn’t necessary! Just apply one coat per day for 5 consecutive days at reasonable intervals (like between 8 am and noon) until you’ve finished your entire project

You must mix the paint before applying it

Mixing the paint before the application is a must. The epoxy will not adhere properly to the surface if you don’t mix it properly, so make sure you have good mixing tools and follow the directions carefully.

You will need:

  • A stir stick or drill motor
  • A heat-resistant container (a large bowl)

You need to keep your structure at 60-90 degrees for about 3 days for the best results

Achieving the best results with EpoxyShield requires a bit of patience and dedication, but it’s nothing you can’t handle.

First, check the temperature in your garage or workshop. You need to keep your structure at 60-90 degrees for about three days for the best results. (You can extend this time if you want.) The warmer the environment is, the faster it will cure; however, if you live in a colder climate and don’t have access to an indoor workspace where you can keep your structure warm enough without freezing yourself out of your house and home, then just be patient! Exposure to cold temperatures will slow down the curing process—but rest assured that when conditions are right again and everything goes back up to 60 degrees or more after being left overnight at room temperature on its side (or bottom), it will still adhere just as well as when used correctly under normal conditions.

You can do it yourself but you get what you pay for

EpoxyShield is a professional-grade product and it’s not cheap. If you’re going to use it, use it correctly and according to the manufacturer’s directions. It is not a do-it-yourself product.



Epoxyshield is a product that has been around for years, and it’s still used today by many DIYers who want to protect their surfaces from stains, grease, and water damage. It’s easy to apply and provides a durable coating for your floors or walls that can last for several years with proper care. While this product does have its drawbacks (costs twice as much as regular paint), it’s still worth considering if you want something better than just clear gloss coatings from your local hardware store but doesn’t want to go all out on professional-grade varnishes or polyurethane finishes either!

Visit and learn more at The Paver Sealer Store!

Share the Post:

Related Posts

Join Our Newsletter