Sale!

ULTRA SEAL – Classic Gloss Wet Look Paver Sealer

Ultra Seal Classic Gloss Water-based 2 Component Urethane Wet Look Paver Sealer. Enhances color & locks joint sand. Also has excellent abrasion & chemical resistance.

  • Can be applied almost immediately after cleaning (works with the water)
  • Provides a Protective Barrier
  • May be applied to damp surfaces
  • User, pet and environmentally friendly
  • Minimal odor
  • Will not harm vegetation
  • Inhibits weed growth and insect infestations
  • Exceptional sand joint stabilization
  • Eliminates the need for polymeric sand
  • VOC compliant in all 50 states
  • UV Protection
  • Two-Part Urethane
  • Classic “Wet Look” color enhancement
  • Hot tire mark resistant
  • 48% solids Formula
  • Mold and Algae Inhibitor

Theoretical coverage rate is 200-300 sqft per gallon dependent on the porosity of the substrate and the width of the sand joint. More porous surfaces will take more sealer. Adjust accordingly.

Application Instructions:

SURFACE PREPARATION: Pressure wash all surfaces to be sealed to remove all dirt and debris. Sealer can be applied to damp pavers.

STRIPPING: If previous sealer is hazed or peeling strip prior to sealing.

MIXING: 4 parts A to 1 part B
Add 1 gallon of part B to
4 gallons of part A. Mix continuously for 2 minutes using a paddle mixer.

FLOOD COAT: Dilute 1 gallon of concentrated sealer with 4 gallons of water. Wait 30 minutes or until the sealer has turned clear and is tacky before applying the finish coat.

FINISH COAT: Dilute 1 gallon of concentrated sealer with 1 gallon of water. Additional coats may be necessary to achieve the desired finish. This depends on the porosity of the paver and the width of the sand joint.

Ultra Seal Classic Gloss Wet Look Paver Sealer is produced and distributed by The Paver Sealer Store

 

$279.00

ULTRA SEAL – Classic Gloss Wet Look Paver Sealer

Description

ULTRA – Wet Look is a two-component urethane which provides deep color enhancement and joint stabilization by locking the sand in-between the joints in place, forms a long-lasting protective barrier on the surface of the pavers or concrete, protecting them from the natural elements and the suns harmful UV rays. Not only is it user friendly, but it produces a consistent finish that wears evenly over time.

All of products are environmentally friendly, bio-degradable, will not harm vegetation, pet friendly, and are commercial quality – formulated with the contractor in mind. All products are VOC's compliant and can be used in all 50 states.

Click here for more before and after photos.

 

Additional information

Weight47 lbs
Dimensions12 × 12 × 16 in
Brand

The Paver Sealer Store

Reviews

There are no reviews yet.

Be the first to review “ULTRA SEAL – Classic Gloss Wet Look Paver Sealer”

SURFACE PREPARATION

For freshly poured concrete: Apply after concrete sets for at least 24 hours. Make sure no water puddles are present. Concrete may be slightly wet before applying.

For fully cured concrete: Remove all dirt, wax, dust, mildew, and loose or scaling material with a scraper, wire brush, or stiff bristle brush. Grease, wax, and oil should be removed by scrubbing with CLEAR PINK STUFF or a heavy duty detergent in warm water. Rinse thoroughly with clean water. Allow to dry. If using a pressure washer, do not use on a pressure setting above 1750 psi to avoid damaging the concrete. Remember, concrete acts like a sponge – pressure washing and general cleaning may trap residual moisture in the concrete. To check for trapped moisture, tape a 12”x12” piece of 3 mil plastic or aluminum foil tightly on all four edges to the surface. Remove it after 24 hours. If the floor side of the plastic or foil is damp, allow additional drying and repeat the test.

EFFLORESCENCE: A white, powdery, crystal-like deposit visible on the masonry surface, should be removed. CLEAN UP EFFLORESCENCE REMOVER or muriatic acid, used according to manufacturer’s directions, are effective efflorescence removal agents. All masonry surfaces are subject to occurrences of efflorescence. Properly prepared concrete should look and feel like medium grit sandpaper. If concrete remains smooth, repeat etching procedure. Test concrete porosity by sprinkling a few drops of water on to the surface in several areas. If the water is readily absorbed, you are ready to paint. If it beads or lays on the surface, additional cleaning and etching is needed. Rinse thoroughly with clean water and allow to dry for 24 hours.

NOTE: Rinse etching solutions thoroughly. Etching solutions allowed to dry on masonry surfaces prevent proper curing of ECO SHIELD DRY LOOK PENETRATING CONCRETE SEALER and may result in the ECO SHIELD DRY LOOK PENETRATING CONCRETE SEALER appearing milky when dry. Patch all holes and cracks with a masonry crack filler or a suitable cement-based patching compound. Be sure to smooth the patch evenly. Allow the patched area to dry thoroughly.

APPLICATION

Apply only when air and surface temperature is above 50° F and humidity below 70%. Do not apply if raining or if it will rain within 48 hours of application. ECO SHIELD DRY LOOK PENETRATING CONCRETE SEALER appears milky in the pail but dries clear. Apply by brush, roller, spray, or squeegee. Spread evenly – do not allow puddles or a heavy surface film to
occur. Apply one coat using thin even strokes. Extremely porous surfaces may require a second coat. Allow 6 hours drying time between coats. Additional coats will cause surface to be
slippery when wet. On light-colored surfaces, some darkening may take place; test in an inconspicuous area to be sure darkening does not occur. May be applied to surfaces previously coated with a similar treatment. For best results, test a small area for proper adhesion prior to coating entire surface.

THINNING
Due to variations in porosity, when applied over flagstone, slate, terrazzo, dense smooth or light colored concrete, thin with clean, moderately warm water 10%—20% to minimize sheen.

In addition, light colored concrete may darken unevenly due to variations in porosity. Test on a small area to see final effect.