Epoxy-garage-floor

Water Based Epoxy Concrete floor and Concrete Block Wall Waterproofer

Water-Based Epoxy is a self-priming two component
floor concrete floor system. Also provides a tough
waterproof and scratch resistant interior concrete block
wall coating system. Three parts resin to One- part
epoxy hardener.

Available in Tint bases and Premixed Colors

$109.87

Water Based Epoxy Concrete floor and Concrete Block Wall Waterproofer

Description

Typical Applications:
Retail and Commercial Flooring
Concrete block walls.
Garage and Showroom Floors
High-Traffic Interior Applications

Approved Topcoats:
Solvent or Water-Based Urethane and 100 solids .
Also approved for wood, concrete and laminate countertops

Surface Prep & Priming:
Grind concrete floors to CSP-3, vacuum dust, wipe with
Denatured alcohol.

Mixing:
Three parts A to 1-part B by volume.
Mixing full kits Add premeasured Part B to Part A Mix for
2 minutes with mechanical mixing. Wearing spike shoes
immediately pour mixed material on the floor and
spread using a flat squeegee or for smaller projects can
be dipped and rolled using 3/8” epoxy roller.

Metallic Applications:
Excellent primer for metallic applications. Premixed
black primer kits available.

Coverage:

1 gallon will cover approximately
Porous Concrete block 200-250 sq.ft./gal.
Receiver coat for vinyl chips 200-250 sq.ft./gal Clear

Finish Coat 250-300 sq.ft./gal.

Best if applied at temperatures between
55-90 degrees Fahrenheit.

Broadcasting Vinyl Chips:
Apply pigmented epoxy basecoat at 200 sq.ft. per gallon
Vinyl flake on 250 sq.ft.

Light 1lb. Heavy 4lbs. Full 25lbs.

After epoxy is spread and back rolled divide chips in
equal portions then throw vinyl chips upwards let them
drop in the wet epoxy. Let cure 24hrs. Then scrape and
vacuum up loose flakes. After scraping and vacuuming
several times. Apply coat of Polyaspartic Clear
or using a magic trowel pull seal coat across the flake at
180 sq. ft per gallon. A Water-Based Two Component Urethane is
also an excellent choice for low odor applications.

Dry-time & Recoat:

Tack free/foot traffic: 12 hrs. Recoat 24 hrs.
Heavy foot traffic 48 hrs. Vehicular Traffic 3 days.
Lightly sand the surface and wipe down with denatured
alcohol or acetone before applying additional coats or
finish coats.

Exterior Applications:

Unless installed as a primer with pigmented Urethane
Topcoats. Not recommended as clear epoxy will amber.

Handling, Storage, Disposal & Clean-up:

  • May irritate eyes wear gloves
  • Store in clean dry area do not freeze
  • Dispose in accordance with all state local and federal
    laws
  • Clean-up tools and equipment with water
  • Regulatory
  • Less than 250 grams/liter
  • Meets all VOC categories in US / except SCAQMD

Warranty:

Material only if proven defective, no labor

Additional information

Weight23 lbs
Dimensions13 × 13 × 13 in
Base Color

Clear, Gray, Tan

Reviews

There are no reviews yet.

Be the first to review “Water Based Epoxy Concrete floor and Concrete Block Wall Waterproofer”

Related products

Ultra Seal Penetrating Natural Stone Sealer

ADVANTAGES

  • Reduces water absorption into the substrate, thus reducing spalling due to freeze thaw and efflorescence, thereby increasing the life of the substrate.
  • Colorless and non-yellowing protection preserves the natural appearance of the substrate.
  • Penetrating & breathable
  • Water based and Environmentally Friendly
  • May be applied to damp surfaces
  • May be painted over
  • Inhibits mold and algae growth
  • Inhibits salt water infiltration

RECOMMENDED USES: For properly prepared, unsealed natural stone, concrete walls, foundations, pre-cast concrete, block, brick and most aggregate surfaces.

SURFACE PREPARATION: Substrate must be pressure washed and cleaned  prior to application of Penetrating Concrete Sealer and Damp Proofer. Surface should be cleaned and treated for organic growth and oil with CLEAR PINK STUFF prior to application. Efflorescence should be treated with CLEAN UP Efflorescence Remover.

APPLICATION INFORMATION: Apply with brush, roller, or pump sprayer. When spraying, use a fan or cone tip designed for water based coatings. Apply when surface and air temperatures are above 60° Fahrenheit and rising. Do not apply if the threat of rain exists within 12 hours.

  • Do not over apply or allow product to puddle.
  • Wet on Wet application – apply product until it begins to repel itself.
  • Wipe off excess.
  • Do not apply to a surface that was previously sealed with a film-forming or topical sealer
  • May be applied to damp surface, however, do not apply when standing water is present
  • May be used as a Moisture Vapor Barrier prior to applying an coating

Coverage: Coverage will depend on porosity of the substrate. Coverage averages up to 250 square feet per gallon depending on the porosity.