Shop

F9-doubloe-eagle-1-gallon

$49.00$180.00

F9BARC-gallon-jugs

$56.00$209.00

terratone-467

$70.00$285.00

Paver Seal Rx 5 gal

Original price was: $239.00.Current price is: $221.75.

SURFACES WHERE TERATONE 467 EXCELS:

  • High Traffic Areas: TERATONE 467 provides a tough and durable barrier to protect high traffic areas from dirt, spills, and stains.

  • Very Porous Surfaces: Porous surfaces absorb stains very easily. TERATONE 467’s protective coating inhibits absorption by porous material.

  • Outdoor Surfaces: TERATONE 467 excels against the constant threats faced by outdoor surfaces. TERATONE 467 protects from the effects of weathering, rain, and UV damage.

SURFACE PREPARATION:

Always be sure the surface is clean, dry, and free from any dirt, grease, oil, wax, or other contaminants. Read the entire label before using. Use only as directed. Always test on a small piece of material or a small inconspicuous area to determine suitability. Ensure the area is well ventilated. Ideal surface temperature should be between 60°F and 80°F. Product works best when it is the first substance applied to the surface, insuring proper penetration.

APPLICATION:

For best results, apply TERATONE 467 with a short nap paint roller(1/4”- 1/2”). Spread in thin coats, evenly and uniformly, leaving no puddles. Allow 8-24 hours to dry before adding a second coat. May also be applied with spray applicator, natural fiber paint brush, roller, or lint free rag.

CLEANUP

Xylene or similar solvent can be used to clean tools.

MAGIC is a deep penetrating, siloxane water repellant which produces a transparent protective barrier across the surface of a stone. MAGIC fills the pores and capillaries of the stone, and forms an invisible, vapor permeable membrane across the surface. This coating repels moisture from the surface while allowing the stone to breathe. MAGIC has no visible film, and leaves surfaces looking natural with no change in appearance.

MAGIC inhibits mold, mildew, and efflorescence, as well as damage caused by the constant absorption and evaporation of water from the stone. MAGIC penetrates immediately, deeply, and effectively, providing a long lasting protective barrier.

For use on Brick, Brick Pavers, Unglazed Ceramic Tile, Clay Tiles, European Clay Pavers, Concrete, Grout Joints, Saltillo Tiles, Travertine, Marble, Granite, or any stone surface when a natural look is desired. MAGIC serves as an excellent grout release. For interior or exterior use.

Enhancing Impregnating Natural Stone Sealer is a color enhancing, slow drying, deep penetrating, solvent based acrylic sealer for interior or exterior use. Ultra Seal Enhancing Impregnating Natural Stone Sealer's slow drying nature allows it to penetrate deep before setting. Will enhance the natural colors of most surfaces. Very effective at sealing and protecting dense and smooth surfaces such as quarry tile, ceramic tile, slate, unfinished marble, terrazzo, travertine, smooth cement, and all other cementitious materials. Recommended for use on unglazed surfaces when NO gloss or a SATIN finish with color enhancement is desired.

RECOMMENDED SURFACES
• Travertine
• Brazilian & Spanish Tile
• Unglazed Tile
• Marble
• Stone, Brick, & Clay Pavers
• Exposed Aggregates
• Quarry Tile

COVERAGE
For very porous surfaces: 1st coat: 150-200 sq. ft./gallon.
2nd coat 300-400 sq. ft./gallon.

For average density surfaces: 1st coat: 250-300+ sq.ft./gallon.
2nd coat 400+ sq. ft./gallon.
For very dense surfaces: 1.5x avg. density coverage Generally, the sealer will go twice as far on the 2nd coat as it did on the 1st coat.

Allow 24 hours between coats.

SURFACE PREPARATION

Always be sure surface is clean, dry, and free from any dirt, grease, oil, wax, or other contaminant. Read the entire label before using. Use only as directed. Always test on a small piece of material or a small inconspicuous area to determine suitability. Ensure the area is well ventilated. Ideal surface temperature should be between 60°F and 80°F. Product works best when it is the first substance applied to the surface, insuring proper penetration.

APPLICATION

Ultra Seal Enhancing Impregnating Natural Stone Sealer may be applied with spray applicator, brush, roller, or lint free rag. Spread evenly and uniformly- cover entire area, leaving no puddles. Avoid puddles by wiping up excess. Allow 24 hours between coats to ensure it has dried completely.
No buffing required.

SMOOTH SURFACES: apply Ultra Seal Enhancing Impregnating Natural Stone Sealer with a lint free cloth or short nap roller.

ROUGH SURFACES: apply with a 1⁄2 to 3⁄4 inch nap paint roller or paint brush.

VOC: 1.09 lb./gallon, 130.66 g/L

STORAGE AND HANDLING

CAUTION: Highly flammable & combustible liquid and vapor. Do not handle until all safety precautions have been read and
understood.

Handling: Do not get in eyes, on skin, or on clothing. Do not breathe vapors or mists. Keep container closed and tightly sealed when not in use. Keep away from sources of ignition – No
smoking. Take measures to prevent the buildup of electrostatic charge.

Conditions for safe storage: Keep in tightly closed, properly labeled containers. Keep in a cool, well-ventilated place.
Materials to avoid: Do not store with the following product types: Strong oxidizing agents, Explosives, Gases.

FIRST AID MEASURES

Eye Contact: Flush eyes with water. Seek medical attention if irritation persists.

Skin Contact: Remove contaminated clothing. Wash with soap and water. Seek medical attention if irritation persists.
Inhalation: If inhaled, remove to fresh air. If respiratory irritation, dizziness, nausea, or unconsciousness occurs, seek immediate medical assistance. In case of unconsciousness place patient stably in side position for transportation.

Ingestion: Do NOT induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious person. Rinse mouth with water. Seek medical attention if symptoms appear.

SEAL Rx ENHANCE

Seal RX Enhance Stone Sealer is a heavy duty, solvent based, silane-siloxane designed to enhance color, impart water repellency and stain resistance to a wide variety of natural stone, concrete and aggregate surfaces.  The silanes react chemically and bond with the substrate to form an insoluble water-resistant treatment within 24-72 hours after application.

__________________________________________________________________________________________

 

RECOMMENDED USES:

For properly prepared, unsealed natural stone, concrete walls, foundations, pre-cast concrete, block, brick and most aggregate surfaces.

 

SURFACE PREPARATION:

Dirt, grease, grime and any foreign material must be removed before application of SEAL Rx ENHANCE.  Treat surface for mildew.  Oil and grease should be scrubbed with a solution of TSP and water.

 

APPLICATION INFORMATION:  

Apply with brush, roller, airless sprayer or pump sprayer.  When spraying, use a tip designed for gloss coatings.  Apply when surface and air temperatures are above 32 Deg. F and rising.  Do not apply if the threat of rain exists.  Do not over apply or allow product to puddle.

 

  • Always apply a test sample to insure compatibility
  • Do not apply to a surface that was previously treated with another product
  • Take care to cover nearby vegetation, glass, plastic and metals. Seal RX 580 may damage them.
  • May be applied to damp surface, however, do not apply when standing water is present

 

SEAL Rx ENHANCE requires different application methods for smooth and porous/rough surfaces.

 

Smooth surfaces:

  1. Apply with brush, roller or spray
  2. Allow to sit for 30-45 minutes
  3. Wipe off excess material with a t-shirt type material. The excess should be removed similar to removing wax from a car.

 

Porous/Rough surfaces: No wiping is necessary as long as product penetrated and no puddles or excess material is visible.

 

 

RECOMMENDED THINNER:

SEAL Rx ENHANCE does not require thinning and should be used as is, directly from the container.

 

BENEFITS:

 

  • Enhances color of substrate.
  • Reduces water absorption into the substrate, thus reducing spalling due to freeze thaw and efflorescence, thereby increasing the life of the substrate.
  • Resists staining
  • Colorless and non-yellowing protection preserves the appearance of the substrate.
  • Penetrating & breathable
  • Low VOC
  • May be applied to damp surfaces
  • UV Resistant
  • Reduces mildew growth on surface

 

 

TECHNICAL DATA:

Finish: Enhanced look                                                          

Pigment Type:  None

Solvent Type: Solvent

Density:  8.50 lbs./Gal.

Viscosity @ 75 deg. F (24 deg. C):  Waterlike

Coating VOC: <50 g/l

 

Clean Up: Clean up drips and spills immediately using any type of solvent.  Clean tools and equipment with any type of solvent.

 

Coverage (Theoretical): Coverage will depend on porosity and contour of the surface being coated.  Coverage typically averages 600-800 square feet per gallon.

 

Storage:  After use, make sure to seal lid tightly.  SEAL Rx ENHANCE will gel if left open.

 

Environmental & Safety Information:

Improper handling or use may be hazardous.  Recommended safety precautions for storage, handling and application must be observed.

 

DANGER: 

COMBUSTIBLE!  KEEP OUT OF REACH OF CHILDREN!

Contains flammable solvents.  Causes eye burns.  Vapor is harmful.  May cause allergic skin reaction.  Do not get in eyes, on skin or on clothing.  Wear eye and skin protective equipment when handling.  Wear appropriate, properly fitted respirator (NIOSH.MSHA approved) during and after application unless air monitoring demonstrates vapor/mist levels are below applicable levels.  Follow respirator manufacturer’s recommendations for use.  Keep containers closed when not in use.

First Aid:  In case of eye contact, flush eyes immediately with plenty of fresh water for at least 15 minutes.  Call a physician.  If inhaled, remove to fresh air.  If not breathing, give artificial respiration, preferably mouth to mouth and seek immediate medical assistance.  In case of skin contact, wash immediately with soap and fresh water.  Remove contaminated clothing and launder before use.  Discard shoes if material has penetrated inside surface.

Notice:  Reports have associated repeated and prolonged occupational overexposure to solvent with permanent brain and nervous system damage.  Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal.

 

WARNING! If you scrape, sand or remove old paint, you may release lead dust.  LEAD IS TOXIC.  EXPOSURE CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN.  PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE.  Wear an NIOSH-approved respirator to control lead exposure.  Carefully clean up with a HEPA vacuum and a wet mop.  Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

 

Technical data contained herein is true and accurate at the date of issue, but is subject to change without notice.  An Inseco representative should be contacted with any questions concerning product information or application procedures.  Our products conform to Inseco quality standards, but no other warranty is expressed or implied.  Liability, if any, is limited to the replacement of product or purchase price.