Epoxy concrete coatings are great for any environment. They’re easy to install, affordable and they’ll last for years. Decorative epoxies
A Stamped concrete driveway can be an attractive and economical way to improve your home. Stamped concrete is not only
Stamped concrete is a great solution for many flooring needs. The process of creating a stamped concrete floor involves a
Join our newsletter to stay updated
Porous materials like natural and man-made stone, concrete, stucco and masonry will start to break down, chalk, pit, crack, and/or stain when subjected to salt, water infiltration, freeze/thaw cycle, harsh weather, oil, and UV rays. The only way to prevent damage and deterioration is to protect your surfaces is with a top quality sealer.
- Water based penetrating sealer
- Ideal masonry primer
- Hardens concrete – acts as a densifier
- No Gloss
- Natural Look
- Dense Natural Stone
MAGIC is a deep penetrating, siloxane water repellant which produces a transparent protective barrier across the surface of a stone. MAGIC fills the pores and capillaries of the stone, and forms an invisible, vapor permeable membrane across the surface. This coating repels moisture from the surface while allowing the stone to breathe. MAGIC has no visible film, and leaves surfaces looking natural with no change in appearance.
Ultra Seal Enhancing Impregnating Natural Stone Sealer is a color enhancing, slow drying, deep penetrating, solvent based acrylic sealer for interior or exterior use. Ultra Seal Enhancing Impregnating Natural Stone Sealer’s slow drying nature allows it to penetrate deep before setting. Will enhance the natural colors of most surfaces. Very effective at sealing and protecting dense and smooth surfaces such as quarry tile, ceramic tile, slate, unfinished marble, terrazzo, travertine, smooth cement, and all other cementitious materials. Recommended for use on unglazed surfaces when NO gloss or a SATIN finish with color enhancement is desired.
Water-Based Epoxy is a self-priming two component
floor concrete floor system. Also provides a tough
waterproof and scratch resistant interior concrete block
wall coating system. Three parts resin to One- part
Available in Tint bases and Premixed Colors
Paver Sealer Remover – Coatings Remover – Paint Stripper
The Paver Sealer Store’s Melt Away Paint Stripper is a highly effective, bio-degradable, environmentally friendly blend that’s been formulated to be non-hazardous and remove various types of coatings. This multi-purpose formula solution has been designed as a paver sealer remover, coating remover and paint stripper all in one. Within minutes, you will start to see the results.
The Paver Sealer Store’s Melt Away Paint Stripper is a great substitute for hazardous blends commonly used for stripping applications.
Ultra Seal Classic Gloss Water-based 2 Component Urethane Wet Look Paver Sealer. Enhances color & locks joint sand. Also has excellent abrasion & chemical resistance.
- Can be applied almost immediately after cleaning (works with the water)
- Provides a Protective Barrier
- May be applied to damp surfaces
- User, pet and environmentally friendly
- Minimal odor
- Will not harm vegetation
- Inhibits weed growth and insect infestations
- Exceptional sand joint stabilization
- Eliminates the need for polymeric sand
- VOC compliant in all 50 states
- UV Protection
- Two-Part Urethane
- Classic “Wet Look” color enhancement
- Hot tire mark resistant
- 48% solids Formula
- Mold and Algae Inhibitor
Theoretical coverage rate is 200-300 sqft per gallon dependent on the porosity of the substrate and the width of the sand joint. More porous surfaces will take more sealer. Adjust accordingly.
SURFACE PREPARATION: Pressure wash all surfaces to be sealed to remove all dirt and debris. Sealer can be applied to damp pavers.
STRIPPING: If previous sealer is hazed or peeling strip prior to sealing.
MIXING: 4 parts A to 1 part B
Add 1 gallon of part B to
4 gallons of part A. Mix continuously for 2 minutes using a paddle mixer.
FLOOD COAT: Dilute 1 gallon of concentrated sealer with 4 gallons of water. Wait 30 minutes or until the sealer has turned clear and is tacky before applying the finish coat.
FINISH COAT: Dilute 1 gallon of concentrated sealer with 1 gallon of water. Additional coats may be necessary to achieve the desired finish. This depends on the porosity of the paver and the width of the sand joint.
Ultra Seal Classic Gloss Wet Look Paver Sealer is produced and distributed by The Paver Sealer Store