Ultra Seal

F9-doubloe-eagle-1-gallon

F9 Double Eagle

$49.00 – $180.00

Select options
f9-efflo-remover-case

F9 Efflorescence & Calcium Remover

$56.00 – $209.00

Select options
F9BARC-gallon-jugs

F9 Barc

$56.00 – $209.00

Select options
agg-sealer-catalina-chemical-888

AGG Sealer Formula 888

$79.00 – $325.00

Select options
rust erase pro 1 gal

Rust Erase Pro – Professional Grade Stain & Rust Remover

$29.50 – $114.00

Select options
A red inked rubber stamp, with a grungy texture to simulate the effect of ink on paper. AI10 EPS is saved in a CMYK color space for optimal printing.

Ultra Seal Ultimate Surface Prep

$32.95 – $159.75

Select options
A red inked rubber stamp, with a grungy texture to simulate the effect of ink on paper. AI10 EPS is saved in a CMYK color space for optimal printing.

Ultra Seal Penetrating Natural Stone Sealer

$279.00

Add to cart
terratone-467

TERATONE 467

$70.00 – $285.00

Select options
clean-up-efflorescence-remover

Clean Up Efflorescence Remover

$34.87

Add to cart
clear-pink-stuff

Clear Pink Stuff

$35.00

Add to cart
A red inked rubber stamp, with a grungy texture to simulate the effect of ink on paper. AI10 EPS is saved in a CMYK color space for optimal printing.

Ultra Seal Eco Shield Dry Look Penetrating Concrete Sealer

$229.00

Add to cart
magic-water-repellent

MAGIC: Water Repellent & Protector

$70.00

Add to cart
A red inked rubber stamp, with a grungy texture to simulate the effect of ink on paper. AI10 EPS is saved in a CMYK color space for optimal printing.

Ultra Seal Enhancing Impregnating Stone Sealer

$119.95 – $479.87

Select options
Epoxy-garage-floor

Water Based Epoxy Concrete floor and Concrete Block Wall Waterproofer

$109.87

Select options
melt away paint stripper pail with label (1)

Melt Away Paint Stripper – Fast, Effective Coating Remover

$57.00 – $269.00

Select options
Ultra-seal-pail-with-label (1)

ULTRA SEAL – Classic Gloss Wet Look Paver Sealer

$279.00

Add to cart

Semi Transparent Color Additives, Dyes, Stains and Tints

$38.95

Select options
Seal RxHD Logo

Seal RX Enhance

$179.00

Add to cart
Paver Seal Rx 5 gal

Paver Seal RX – 5 Gallon

$221.75

Add to cart
Paver Seal Rx 1 gal

Paver Seal RX – 1 Gallon

$56.00

Add to cart

F9 Double Eagle

For use on Concrete, Bricks, Pavers, Tile, Stone, Grout Masonry Hard Surfaces and most surfaces in general. Great for food grease, oils, dumpster pads, loading docks, gas stations, parking garages, tire marks and general cleaning of many surfaces.

DILUTION RATIOS

Very Heavily Soiled Surfaces: Straight

Heavily Soiled Surfaces: 1:1 to 5:1

Moderately Soiled Surfaces: 10:1

Lightly Soiled Surfaces: 20:1

CLEANING INSTRUCTIONS

Direct Application: Pump Sprayer, Electric or Air Diaphragm Spray System.

Dilution will depend on how dirty the area is. Product may be diluted 5:1 to 20:1. Spray on, dwell 2-15 minutes. Manually agitate heavy areas or use floor tool. Surface clean after. Hot water preferred, cold water ok.

Downstream Application: Use a downstream injection system capable of giving you the correct dilution rate for the circumstances. Spray on, dwell 2-15 minutes. Manually agitate heavy areas or use floor tool. Surface clean after. Hot water preferred, cold water ok.

X-Jet Application: Dilute product to give you the correct dilution rate for the circumstances. Spray on, dwell 2-15 minutes. Manually agitate heavy areas or use floor tool. Surface clean after. Hot water preferred, cold water ok.

Note: If areas are extremely soiled, use a 175 floor tool with extra-aggressive mal-grit to agitate.

HOW TO USE AS A NEUTRALIZER

General Neutralizing: 8:1. Spray on surface to be neutralized. Broom in if necessary. Rinse or surface clean. Make stronger to bring final pH of discharge up. Make weaker if you need to adjust final pH down. Always check wastewater to make sure final discharge pH is correct for City BMP’s.

F9 Efflorescence & Calcium Remover

Calcium and Efflorescence Remover is breakthrough in the restoration and cleaning industry. F9 Calcium and Efflorescence Remover is a user friendly, full 31.45% strength muriatic acid replacement. This product combines a buffered, pleasant smelling acid along with an excellent soaping capability to work better at lower concentrations. F9 Calcium and Efflorescence Remover gives the user the advantage of a full strength product while greatly reducing fuming and corrosion, thereby improving overall health and safety risk profile.

F9 Barc

Quantity of 1 Gallon Units. 1 Gallon of BARC concentrate makes up to 3 gallons of cleaner.

F9 BARC is for F9 Authorized Applicators, Contractors and Maintenance Department Use Only. By purchasing F9 products you are agreeing that you are an F9 Authorized Applicator, Contractor or Maintenance Department. Front 9 Restoration, Inc. is not responsible for improper application nor will we be held responsible for any damage caused by improper application of our products.

One Gallon of F9 BARC Makes 1.5 to 3 Gallons of Cleaner. Always Mix F9 with Only Clean Water Prior to Application.
One Gallon of F9 Concrete Rust Remover will cover 400-800′ of Concrete.
Check Out F9 University For Detailed Application Videos.

DO NOT USE ON GLASS

Ultra Seal Ultimate Surface Prep

FOR CLEANING:

  • Brick Pavers
  • Irrigation Stains
  • Rust Stains
  • Limestone
  • Brownstone
  • Unpolished Marble
  • Precast
  • Exposed Aggregate
  • Concrete
  • Brick
  • Block
  • Terra Cotta
  • Vinyl
  • Metals
  • Wood
  • Synthetic Decking
  • Stucco
  • Sealer Cleaning
  • Unpolished Natural Stone
  • 10:1 Dilution – (can be downstreamed)

Do not allow to come in contact with glass.

Application: Dilute 1 part Ultimate Surface Prep with 10 parts water.  Apply and let dwell for two to three minutes before pressure washing surface. Rinse well.  Heavy staining might require additional applications.

Ultra Seal Penetrating Natural Stone Sealer

ADVANTAGES

  • Reduces water absorption into the substrate, thus reducing spalling due to freeze thaw and efflorescence, thereby increasing the life of the substrate.
  • Colorless and non-yellowing protection preserves the natural appearance of the substrate.
  • Penetrating & breathable
  • Water based and Environmentally Friendly
  • May be applied to damp surfaces
  • May be painted over
  • Inhibits mold and algae growth
  • Inhibits salt water infiltration

RECOMMENDED USES: For properly prepared, unsealed natural stone, concrete walls, foundations, pre-cast concrete, block, brick and most aggregate surfaces.

SURFACE PREPARATION: Substrate must be pressure washed and cleaned  prior to application of Penetrating Concrete Sealer and Damp Proofer. Surface should be cleaned and treated for organic growth and oil with CLEAR PINK STUFF prior to application. Efflorescence should be treated with CLEAN UP Efflorescence Remover.

APPLICATION INFORMATION: Apply with brush, roller, or pump sprayer. When spraying, use a fan or cone tip designed for water based coatings. Apply when surface and air temperatures are above 60° Fahrenheit and rising. Do not apply if the threat of rain exists within 12 hours.

  • Do not over apply or allow product to puddle.
  • Wet on Wet application – apply product until it begins to repel itself.
  • Wipe off excess.
  • Do not apply to a surface that was previously sealed with a film-forming or topical sealer
  • May be applied to damp surface, however, do not apply when standing water is present
  • May be used as a Moisture Vapor Barrier prior to applying an coating

Coverage: Coverage will depend on porosity of the substrate. Coverage averages up to 250 square feet per gallon depending on the porosity.

Clean Up Efflorescence Remover

CLEAN UP Efflorescence Remover is a specially formulated, non-regulated liquid agent designed for use on brick, tile, and concrete surfaces. Clean Up quickly and effectively removes mortar smear, construction dirt, and efflorescence without damaging surrounding surfaces. is 100% Biodegradable, Non-Corrosive, Non-Regulated, and a Non-Skin Irritant.

Proper Shipping Name – Clean Up Efflorescence Remover
Non-Hazardous for Transport by Truck
DOT Hazard Class – Not Regulated
Packing Group – Not Regulated
ID# – None

Available in 1 Gallon Jugs

Clear Pink Stuff

Inhalation: Remove affected person to fresh air; get immediate medical attention with emphasis on hydrofluoric acid exposure. If breathing is difficult, supply oxygen. If breathing has stopped, begin artificial respiration.

Skin: Remove contaminated clothing while flushing affected area with drenching shower for 5 minutes. Launder contaminated clothing before reuse; seek immediate medical attention with emphasis on hydrofluoric acid exposure. Apply 2.5% Calcium Gluconate ointment to contacted area.

Eyes: Check for and remove contact lenses. Immediately flush eyes for 5 minutes in clear running water while holding eyelids open; seek immediate medical attention with emphasis on hydrofluoric acid exposure. Irrigate open eyelids with 500 to 1,000 cc’s of 1% Calcium Gluconate in saline solution.

Ingestion: Drink high amounts of calcium based antacid in water followed by milk or milk of magnesia; DO NOT induce vomiting; never give anything by to an unconscious person; seek immediate medical attention with emphasis on hydrofluoric acid exposure

Ultra Seal Eco Shield Dry Look Penetrating Concrete Sealer

SURFACE PREPARATION

For freshly poured concrete: Apply after concrete sets for at least 24 hours. Make sure no water puddles are present. Concrete may be slightly wet before applying.

For fully cured concrete: Remove all dirt, wax, dust, mildew, and loose or scaling material with a scraper, wire brush, or stiff bristle brush. Grease, wax, and oil should be removed by scrubbing with CLEAR PINK STUFF or a heavy duty detergent in warm water. Rinse thoroughly with clean water. Allow to dry. If using a pressure washer, do not use on a pressure setting above 1750 psi to avoid damaging the concrete. Remember, concrete acts like a sponge – pressure washing and general cleaning may trap residual moisture in the concrete. To check for trapped moisture, tape a 12”x12” piece of 3 mil plastic or aluminum foil tightly on all four edges to the surface. Remove it after 24 hours. If the floor side of the plastic or foil is damp, allow additional drying and repeat the test.

EFFLORESCENCE: A white, powdery, crystal-like deposit visible on the masonry surface, should be removed. CLEAN UP EFFLORESCENCE REMOVER or muriatic acid, used according to manufacturer’s directions, are effective efflorescence removal agents. All masonry surfaces are subject to occurrences of efflorescence. Properly prepared concrete should look and feel like medium grit sandpaper. If concrete remains smooth, repeat etching procedure. Test concrete porosity by sprinkling a few drops of water on to the surface in several areas. If the water is readily absorbed, you are ready to paint. If it beads or lays on the surface, additional cleaning and etching is needed. Rinse thoroughly with clean water and allow to dry for 24 hours.

NOTE: Rinse etching solutions thoroughly. Etching solutions allowed to dry on masonry surfaces prevent proper curing of ECO SHIELD DRY LOOK PENETRATING CONCRETE SEALER and may result in the ECO SHIELD DRY LOOK PENETRATING CONCRETE SEALER appearing milky when dry. Patch all holes and cracks with a masonry crack filler or a suitable cement-based patching compound. Be sure to smooth the patch evenly. Allow the patched area to dry thoroughly.

APPLICATION

Apply only when air and surface temperature is above 50° F and humidity below 70%. Do not apply if raining or if it will rain within 48 hours of application. ECO SHIELD DRY LOOK PENETRATING CONCRETE SEALER appears milky in the pail but dries clear. Apply by brush, roller, spray, or squeegee. Spread evenly – do not allow puddles or a heavy surface film to
occur. Apply one coat using thin even strokes. Extremely porous surfaces may require a second coat. Allow 6 hours drying time between coats. Additional coats will cause surface to be
slippery when wet. On light-colored surfaces, some darkening may take place; test in an inconspicuous area to be sure darkening does not occur. May be applied to surfaces previously coated with a similar treatment. For best results, test a small area for proper adhesion prior to coating entire surface.

THINNING
Due to variations in porosity, when applied over flagstone, slate, terrazzo, dense smooth or light colored concrete, thin with clean, moderately warm water 10%—20% to minimize sheen.

In addition, light colored concrete may darken unevenly due to variations in porosity. Test on a small area to see final effect.

Ultra Seal Enhancing Impregnating Stone Sealer

Enhancing Impregnating Natural Stone Sealer is a color enhancing, slow drying, deep penetrating, solvent based acrylic sealer for interior or exterior use. Ultra Seal Enhancing Impregnating Natural Stone Sealer's slow drying nature allows it to penetrate deep before setting. Will enhance the natural colors of most surfaces. Very effective at sealing and protecting dense and smooth surfaces such as quarry tile, ceramic tile, slate, unfinished marble, terrazzo, travertine, smooth cement, and all other cementitious materials. Recommended for use on unglazed surfaces when NO gloss or a SATIN finish with color enhancement is desired.

RECOMMENDED SURFACES
• Travertine
• Brazilian & Spanish Tile
• Unglazed Tile
• Marble
• Stone, Brick, & Clay Pavers
• Exposed Aggregates
• Quarry Tile

COVERAGE
For very porous surfaces: 1st coat: 150-200 sq. ft./gallon.
2nd coat 300-400 sq. ft./gallon.

For average density surfaces: 1st coat: 250-300+ sq.ft./gallon.
2nd coat 400+ sq. ft./gallon.
For very dense surfaces: 1.5x avg. density coverage Generally, the sealer will go twice as far on the 2nd coat as it did on the 1st coat.

Allow 24 hours between coats.

SURFACE PREPARATION

Always be sure surface is clean, dry, and free from any dirt, grease, oil, wax, or other contaminant. Read the entire label before using. Use only as directed. Always test on a small piece of material or a small inconspicuous area to determine suitability. Ensure the area is well ventilated. Ideal surface temperature should be between 60°F and 80°F. Product works best when it is the first substance applied to the surface, insuring proper penetration.

APPLICATION

Ultra Seal Enhancing Impregnating Natural Stone Sealer may be applied with spray applicator, brush, roller, or lint free rag. Spread evenly and uniformly- cover entire area, leaving no puddles. Avoid puddles by wiping up excess. Allow 24 hours between coats to ensure it has dried completely.
No buffing required.

SMOOTH SURFACES: apply Ultra Seal Enhancing Impregnating Natural Stone Sealer with a lint free cloth or short nap roller.

ROUGH SURFACES: apply with a 1⁄2 to 3⁄4 inch nap paint roller or paint brush.

VOC: 1.09 lb./gallon, 130.66 g/L

STORAGE AND HANDLING

CAUTION: Highly flammable & combustible liquid and vapor. Do not handle until all safety precautions have been read and
understood.

Handling: Do not get in eyes, on skin, or on clothing. Do not breathe vapors or mists. Keep container closed and tightly sealed when not in use. Keep away from sources of ignition – No
smoking. Take measures to prevent the buildup of electrostatic charge.

Conditions for safe storage: Keep in tightly closed, properly labeled containers. Keep in a cool, well-ventilated place.
Materials to avoid: Do not store with the following product types: Strong oxidizing agents, Explosives, Gases.

FIRST AID MEASURES

Eye Contact: Flush eyes with water. Seek medical attention if irritation persists.

Skin Contact: Remove contaminated clothing. Wash with soap and water. Seek medical attention if irritation persists.
Inhalation: If inhaled, remove to fresh air. If respiratory irritation, dizziness, nausea, or unconsciousness occurs, seek immediate medical assistance. In case of unconsciousness place patient stably in side position for transportation.

Ingestion: Do NOT induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious person. Rinse mouth with water. Seek medical attention if symptoms appear.

Water Based Epoxy Concrete floor and Concrete Block Wall Waterproofer

Typical Applications:
Retail and Commercial Flooring
Concrete block walls.
Garage and Showroom Floors
High-Traffic Interior Applications

Approved Topcoats:
Solvent or Water-Based Urethane and 100 solids .
Also approved for wood, concrete and laminate countertops

Surface Prep & Priming:
Grind concrete floors to CSP-3, vacuum dust, wipe with
Denatured alcohol.

Mixing:
Three parts A to 1-part B by volume.
Mixing full kits Add premeasured Part B to Part A Mix for
2 minutes with mechanical mixing. Wearing spike shoes
immediately pour mixed material on the floor and
spread using a flat squeegee or for smaller projects can
be dipped and rolled using 3/8” epoxy roller.

Metallic Applications:
Excellent primer for metallic applications. Premixed
black primer kits available.

Coverage:

1 gallon will cover approximately
Porous Concrete block 200-250 sq.ft./gal.
Receiver coat for vinyl chips 200-250 sq.ft./gal Clear

Finish Coat 250-300 sq.ft./gal.

Best if applied at temperatures between
55-90 degrees Fahrenheit.

Broadcasting Vinyl Chips:
Apply pigmented epoxy basecoat at 200 sq.ft. per gallon
Vinyl flake on 250 sq.ft.

Light 1lb. Heavy 4lbs. Full 25lbs.

After epoxy is spread and back rolled divide chips in
equal portions then throw vinyl chips upwards let them
drop in the wet epoxy. Let cure 24hrs. Then scrape and
vacuum up loose flakes. After scraping and vacuuming
several times. Apply coat of Polyaspartic Clear
or using a magic trowel pull seal coat across the flake at
180 sq. ft per gallon. A Water-Based Two Component Urethane is
also an excellent choice for low odor applications.

Dry-time & Recoat:

Tack free/foot traffic: 12 hrs. Recoat 24 hrs.
Heavy foot traffic 48 hrs. Vehicular Traffic 3 days.
Lightly sand the surface and wipe down with denatured
alcohol or acetone before applying additional coats or
finish coats.

Exterior Applications:

Unless installed as a primer with pigmented Urethane
Topcoats. Not recommended as clear epoxy will amber.

Handling, Storage, Disposal & Clean-up:

  • May irritate eyes wear gloves
  • Store in clean dry area do not freeze
  • Dispose in accordance with all state local and federal
    laws
  • Clean-up tools and equipment with water
  • Regulatory
  • Less than 250 grams/liter
  • Meets all VOC categories in US / except SCAQMD

Warranty:

Material only if proven defective, no labor

Melt Away Paint Stripper – Fast, Effective Coating Remover

 

  • Removes multiple layers in one application.
  • Effective on , pint, acrylic sealers, epoxies & enamels
  • Strong emulsifier package lifts sealer in 15-20 minutes
  • Water soluble clean rinse technology
  • Sprayable VOC compliant
  • Methylene chloride and caustic free
  • Non Flammable
  • Dual action – lifts and emulsifies the coating
  • Bio-degradable and Environmentally Friendly
  • Ships DOT Non-Flammable, Non-Hazardous to all 50 states including California

Warrantied against material free of defects.  Not warrantied against labor.

Application Instructions:

Pour contents into a pump-up sprayer system, cover and or dampen with water any grass, plants, or flowers they may encounter with overspray, then uniformly apply a flood coat of Melt Away . Hold sprayer tip 12” from the surface while spraying and let dwell for 15-20 minutes (excessive layers may need longer dwell times or reapplication) until sealer and other coatings start to turn grayish or shows signs of peeling.

Using a plastic putty knife, you should be able to scrape the coating from the substrate. At this point it is ready to rinse utilizing a pressure washer with a turbo tip. The use of a fan tip as zero tip is not recommended as it will leave etch the substrate. Melt Away Paint Stripper and paver sealer remover can also be applied using a ½ nap roller as well.

Distributed by , LLC

ULTRA SEAL – Classic Gloss Wet Look Paver Sealer

ULTRA – Wet Look is a two-component urethane which provides deep color enhancement and joint stabilization by locking the sand in-between the joints in place, forms a long-lasting protective barrier on the surface of the pavers or concrete, protecting them from the natural elements and the suns harmful UV rays. Not only is it user friendly, but it produces a consistent finish that wears evenly over time.

All of products are environmentally friendly, bio-degradable, will not harm vegetation, pet friendly, and are commercial quality – formulated with the contractor in mind. All products are VOC's compliant and can be used in all 50 states.

Click here for more before and after photos.