Paint Stripper

F9-doubloe-eagle-1-gallon

$49.00$180.00

F9BARC-gallon-jugs

$56.00$209.00

terratone-467

$70.00$285.00

FOR CLEANING:

  • Brick Pavers
  • Irrigation Stains
  • Rust Stains
  • Limestone
  • Brownstone
  • Unpolished Marble
  • Precast
  • Exposed Aggregate
  • Concrete
  • Brick
  • Block
  • Terra Cotta
  • Vinyl
  • Metals
  • Wood
  • Synthetic Decking
  • Stucco
  • Sealer Cleaning
  • Unpolished Natural Stone
  • 10:1 Dilution – (can be downstreamed)

Do not allow to come in contact with glass.

Application: Dilute 1 part Ultimate Surface Prep with 10 parts water.  Apply and let dwell for two to three minutes before pressure washing surface. Rinse well.  Heavy staining might require additional applications.

ADVANTAGES

  • Reduces water absorption into the substrate, thus reducing spalling due to freeze thaw and efflorescence, thereby increasing the life of the substrate.
  • Colorless and non-yellowing protection preserves the natural appearance of the substrate.
  • Penetrating & breathable
  • Water based and Environmentally Friendly
  • May be applied to damp surfaces
  • May be painted over
  • Inhibits mold and algae growth
  • Inhibits salt water infiltration

RECOMMENDED USES: For properly prepared, unsealed natural stone, concrete walls, foundations, pre-cast concrete, block, brick and most aggregate surfaces.

SURFACE PREPARATION: Substrate must be pressure washed and cleaned  prior to application of Penetrating Concrete Sealer and Damp Proofer. Surface should be cleaned and treated for organic growth and oil with CLEAR PINK STUFF prior to application. Efflorescence should be treated with CLEAN UP Efflorescence Remover.

APPLICATION INFORMATION: Apply with brush, roller, or pump sprayer. When spraying, use a fan or cone tip designed for water based coatings. Apply when surface and air temperatures are above 60° Fahrenheit and rising. Do not apply if the threat of rain exists within 12 hours.

  • Do not over apply or allow product to puddle.
  • Wet on Wet application – apply product until it begins to repel itself.
  • Wipe off excess.
  • Do not apply to a surface that was previously sealed with a film-forming or topical sealer
  • May be applied to damp surface, however, do not apply when standing water is present
  • May be used as a Moisture Vapor Barrier prior to applying an coating

Coverage: Coverage will depend on porosity of the substrate. Coverage averages up to 250 square feet per gallon depending on the porosity.

SURFACE PREPARATION

For freshly poured concrete: Apply after concrete sets for at least 24 hours. Make sure no water puddles are present. Concrete may be slightly wet before applying.

For fully cured concrete: Remove all dirt, wax, dust, mildew, and loose or scaling material with a scraper, wire brush, or stiff bristle brush. Grease, wax, and oil should be removed by scrubbing with CLEAR PINK STUFF or a heavy duty detergent in warm water. Rinse thoroughly with clean water. Allow to dry. If using a pressure washer, do not use on a pressure setting above 1750 psi to avoid damaging the concrete. Remember, concrete acts like a sponge – pressure washing and general cleaning may trap residual moisture in the concrete. To check for trapped moisture, tape a 12”x12” piece of 3 mil plastic or aluminum foil tightly on all four edges to the surface. Remove it after 24 hours. If the floor side of the plastic or foil is damp, allow additional drying and repeat the test.

EFFLORESCENCE: A white, powdery, crystal-like deposit visible on the masonry surface, should be removed. CLEAN UP EFFLORESCENCE REMOVER or muriatic acid, used according to manufacturer’s directions, are effective efflorescence removal agents. All masonry surfaces are subject to occurrences of efflorescence. Properly prepared concrete should look and feel like medium grit sandpaper. If concrete remains smooth, repeat etching procedure. Test concrete porosity by sprinkling a few drops of water on to the surface in several areas. If the water is readily absorbed, you are ready to paint. If it beads or lays on the surface, additional cleaning and etching is needed. Rinse thoroughly with clean water and allow to dry for 24 hours.

NOTE: Rinse etching solutions thoroughly. Etching solutions allowed to dry on masonry surfaces prevent proper curing of ECO SHIELD DRY LOOK PENETRATING CONCRETE SEALER and may result in the ECO SHIELD DRY LOOK PENETRATING CONCRETE SEALER appearing milky when dry. Patch all holes and cracks with a masonry crack filler or a suitable cement-based patching compound. Be sure to smooth the patch evenly. Allow the patched area to dry thoroughly.

APPLICATION

Apply only when air and surface temperature is above 50° F and humidity below 70%. Do not apply if raining or if it will rain within 48 hours of application. ECO SHIELD DRY LOOK PENETRATING CONCRETE SEALER appears milky in the pail but dries clear. Apply by brush, roller, spray, or squeegee. Spread evenly – do not allow puddles or a heavy surface film to
occur. Apply one coat using thin even strokes. Extremely porous surfaces may require a second coat. Allow 6 hours drying time between coats. Additional coats will cause surface to be
slippery when wet. On light-colored surfaces, some darkening may take place; test in an inconspicuous area to be sure darkening does not occur. May be applied to surfaces previously coated with a similar treatment. For best results, test a small area for proper adhesion prior to coating entire surface.

THINNING
Due to variations in porosity, when applied over flagstone, slate, terrazzo, dense smooth or light colored concrete, thin with clean, moderately warm water 10%—20% to minimize sheen.

In addition, light colored concrete may darken unevenly due to variations in porosity. Test on a small area to see final effect.

Enhancing Impregnating Natural Stone Sealer is a color enhancing, slow drying, deep penetrating, solvent based acrylic sealer for interior or exterior use. Ultra Seal Enhancing Impregnating Natural Stone Sealer's slow drying nature allows it to penetrate deep before setting. Will enhance the natural colors of most surfaces. Very effective at sealing and protecting dense and smooth surfaces such as quarry tile, ceramic tile, slate, unfinished marble, terrazzo, travertine, smooth cement, and all other cementitious materials. Recommended for use on unglazed surfaces when NO gloss or a SATIN finish with color enhancement is desired.

RECOMMENDED SURFACES
• Travertine
• Brazilian & Spanish Tile
• Unglazed Tile
• Marble
• Stone, Brick, & Clay Pavers
• Exposed Aggregates
• Quarry Tile

COVERAGE
For very porous surfaces: 1st coat: 150-200 sq. ft./gallon.
2nd coat 300-400 sq. ft./gallon.

For average density surfaces: 1st coat: 250-300+ sq.ft./gallon.
2nd coat 400+ sq. ft./gallon.
For very dense surfaces: 1.5x avg. density coverage Generally, the sealer will go twice as far on the 2nd coat as it did on the 1st coat.

Allow 24 hours between coats.

SURFACE PREPARATION

Always be sure surface is clean, dry, and free from any dirt, grease, oil, wax, or other contaminant. Read the entire label before using. Use only as directed. Always test on a small piece of material or a small inconspicuous area to determine suitability. Ensure the area is well ventilated. Ideal surface temperature should be between 60°F and 80°F. Product works best when it is the first substance applied to the surface, insuring proper penetration.

APPLICATION

Ultra Seal Enhancing Impregnating Natural Stone Sealer may be applied with spray applicator, brush, roller, or lint free rag. Spread evenly and uniformly- cover entire area, leaving no puddles. Avoid puddles by wiping up excess. Allow 24 hours between coats to ensure it has dried completely.
No buffing required.

SMOOTH SURFACES: apply Ultra Seal Enhancing Impregnating Natural Stone Sealer with a lint free cloth or short nap roller.

ROUGH SURFACES: apply with a 1⁄2 to 3⁄4 inch nap paint roller or paint brush.

VOC: 1.09 lb./gallon, 130.66 g/L

STORAGE AND HANDLING

CAUTION: Highly flammable & combustible liquid and vapor. Do not handle until all safety precautions have been read and
understood.

Handling: Do not get in eyes, on skin, or on clothing. Do not breathe vapors or mists. Keep container closed and tightly sealed when not in use. Keep away from sources of ignition – No
smoking. Take measures to prevent the buildup of electrostatic charge.

Conditions for safe storage: Keep in tightly closed, properly labeled containers. Keep in a cool, well-ventilated place.
Materials to avoid: Do not store with the following product types: Strong oxidizing agents, Explosives, Gases.

FIRST AID MEASURES

Eye Contact: Flush eyes with water. Seek medical attention if irritation persists.

Skin Contact: Remove contaminated clothing. Wash with soap and water. Seek medical attention if irritation persists.
Inhalation: If inhaled, remove to fresh air. If respiratory irritation, dizziness, nausea, or unconsciousness occurs, seek immediate medical assistance. In case of unconsciousness place patient stably in side position for transportation.

Ingestion: Do NOT induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious person. Rinse mouth with water. Seek medical attention if symptoms appear.

Typical Applications:
Retail and Commercial Flooring
Concrete block walls.
Garage and Showroom Floors
High-Traffic Interior Applications

Approved Topcoats:
Solvent or Water-Based Urethane and 100 solids .
Also approved for wood, concrete and laminate countertops

Surface Prep & Priming:
Grind concrete floors to CSP-3, vacuum dust, wipe with
Denatured alcohol.

Mixing:
Three parts A to 1-part B by volume.
Mixing full kits Add premeasured Part B to Part A Mix for
2 minutes with mechanical mixing. Wearing spike shoes
immediately pour mixed material on the floor and
spread using a flat squeegee or for smaller projects can
be dipped and rolled using 3/8” epoxy roller.

Metallic Applications:
Excellent primer for metallic applications. Premixed
black primer kits available.

Coverage:

1 gallon will cover approximately
Porous Concrete block 200-250 sq.ft./gal.
Receiver coat for vinyl chips 200-250 sq.ft./gal Clear

Finish Coat 250-300 sq.ft./gal.

Best if applied at temperatures between
55-90 degrees Fahrenheit.

Broadcasting Vinyl Chips:
Apply pigmented epoxy basecoat at 200 sq.ft. per gallon
Vinyl flake on 250 sq.ft.

Light 1lb. Heavy 4lbs. Full 25lbs.

After epoxy is spread and back rolled divide chips in
equal portions then throw vinyl chips upwards let them
drop in the wet epoxy. Let cure 24hrs. Then scrape and
vacuum up loose flakes. After scraping and vacuuming
several times. Apply coat of Polyaspartic Clear
or using a magic trowel pull seal coat across the flake at
180 sq. ft per gallon. A Water-Based Two Component Urethane is
also an excellent choice for low odor applications.

Dry-time & Recoat:

Tack free/foot traffic: 12 hrs. Recoat 24 hrs.
Heavy foot traffic 48 hrs. Vehicular Traffic 3 days.
Lightly sand the surface and wipe down with denatured
alcohol or acetone before applying additional coats or
finish coats.

Exterior Applications:

Unless installed as a primer with pigmented Urethane
Topcoats. Not recommended as clear epoxy will amber.

Handling, Storage, Disposal & Clean-up:

  • May irritate eyes wear gloves
  • Store in clean dry area do not freeze
  • Dispose in accordance with all state local and federal
    laws
  • Clean-up tools and equipment with water
  • Regulatory
  • Less than 250 grams/liter
  • Meets all VOC categories in US / except SCAQMD

Warranty:

Material only if proven defective, no labor

ULTRA – Wet Look is a two-component urethane which provides deep color enhancement and joint stabilization by locking the sand in-between the joints in place, forms a long-lasting protective barrier on the surface of the pavers or concrete, protecting them from the natural elements and the suns harmful UV rays. Not only is it user friendly, but it produces a consistent finish that wears evenly over time.

All of products are environmentally friendly, bio-degradable, will not harm vegetation, pet friendly, and are commercial quality – formulated with the contractor in mind. All products are VOC's compliant and can be used in all 50 states.

Click here for more before and after photos.