Paver Sealant

UltraGloss SX – High Gloss Urethane Sealer
Professional product profile
UltraGloss SX is a ready-to-use 1K urethane sealer for pavers, concrete, brick, natural stone, and compatible epoxy floors. It is built for a bold wet-look finish without the mixing step required by a two-component system.
Selection standardSurface + finish + applicationConfirm all three before ordering.
Real-world application
FinishHigh gloss / wet look
SystemSingle-component 1K urethane
Best forPavers, concrete, brick, natural stone, and compatible epoxy floors
ApplicationRoller or sprayer; apply controlled, even coats
Wet-look protection
Product performance overview
Wet-look and high-gloss sealers should be selected by substrate porosity, the condition of any existing coating, joint condition, desired sheen, weather, and cure window. Film build and appearance depend on thin, controlled application over a properly prepared surface.
Best matched when
The surface is compatible, the desired result includes visible color enhancement, and the applicator can control moisture, coat thickness, and cure conditions.
Key advantages
What this product is designed to deliver
- No catalyst or batch mixing
- Deepens color with a glossy wet look
- Helps protect against water, oil, stains, UV exposure, and everyday wear
- Useful as a high-gloss topcoat when the substrate is compatible
Recommended uses
Where it performs best
Driveways, patios, pool decks, walkways, decorative concrete, and other exterior hardscapes.
Coverage planning
Measure before ordering
Coverage changes with porosity, profile, and application method. Use the Coverage Calculator before ordering.
Open the Coverage Calculator
Job planning
Build the application around product requirements
Confirm the old coating and substrate are compatible, remove contaminants and failed material, repair joints as needed, measure the area, make a representative test patch, and apply only within the product-specific weather and recoat requirements.
Four-stage process
Application overview
1. Clean, profile, and dry the surface according to the product directions.
2. Test a small area to confirm adhesion, color, and final gloss.
3. Apply thin, even coats and avoid puddling or overworking the sealer.
4. Respect the label dry and return-to-service times before foot or vehicle traffic.
Technical noteSurface compatibility, weather, moisture, dilution, mixing, dwell time, and cure requirements vary by product. Read the current label and SDS, test a small area, and follow the product-specific technical directions before full application.
Product questions
Frequently asked questions

Is UltraGloss SX a two-part sealer?
No. UltraGloss SX is a single-component 1K urethane. Do not add a catalyst or hardener.

What finish does UltraGloss SX create?
It is designed for a high-gloss, wet-look finish that enhances the existing color and texture of compatible pavers and concrete.

How much do I need?
Porosity and application method have a major effect on coverage. Measure the area and use the Coverage Calculator before choosing a size.

Expert buying guidanceChoose the right product with confidence.
Confirm the surface, finish, coverage, and application conditions before checkout.
Use Sealer Finder Calculate coverage Application guidance
Browse all professional surface-care products
Ultra Seal Penetrating Natural Stone Sealer
Professional product profile
Ultra Seal Penetrating Natural Stone Sealer is a breathable, water-based penetrating treatment for natural stone, concrete, brick, block, foundations, and aggregate surfaces where the original appearance should remain visible.
Selection standardSurface + finish + applicationConfirm all three before ordering.
Real-world application
FinishNatural / low-sheen appearance
SystemWater-based penetrating and breathable sealer
Best forNatural stone, concrete, brick, block, foundations, precast concrete, and aggregate
ApplicationBrush, roller, or sprayer on a properly prepared substrate
Natural-look protection
Product performance overview
Penetrating protection is chosen when the goal is to reduce water and contaminant absorption without creating a glossy surface film. Porosity, absorption rate, moisture, prior treatments, and the material itself determine whether the product can penetrate and perform as intended.
Best matched when
The surface is porous and absorbent, a natural appearance is preferred, and a test area confirms even penetration without residue or unwanted color change.
Key advantages
What this product is designed to deliver
- Penetrating and breathable protection
- Helps reduce water absorption, salt infiltration, and freeze-thaw stress
- Colorless, non-yellowing natural appearance
- May be applied to appropriately damp surfaces when the product directions allow it
Recommended uses
Where it performs best
Natural-looking protection for stone, concrete, brick, walls, foundations, and other porous mineral surfaces.
Coverage planning
Measure before ordering
Coverage varies with porosity and absorption. Use the Coverage Calculator and confirm the substrate can accept a penetrating treatment.
Open the Coverage Calculator
Job planning
Build the application around product requirements
Identify the substrate, remove soil and residue, allow the surface to reach the required moisture condition, verify absorption, calculate material from tested coverage, and remove excess product exactly as directed.
Four-stage process
Application overview
1. Clean the substrate and remove oil, organic growth, efflorescence, and loose material.
2. Confirm the surface is compatible and test for absorption.
3. Apply evenly without leaving puddles or unabsorbed residue.
4. Allow the treatment to cure according to the product directions before evaluating water repellency.
Technical noteSurface compatibility, weather, moisture, dilution, mixing, dwell time, and cure requirements vary by product. Read the current label and SDS, test a small area, and follow the product-specific technical directions before full application.
Product questions
Frequently asked questions

Will this sealer change the color?
It is designed to preserve a natural appearance rather than create a glossy wet look. Always test first because substrates vary.

Can it be used on natural stone?
Yes, the product is intended for properly prepared, unsealed natural stone and other porous mineral surfaces listed in the product information.

Does penetrating sealer form a film?
This system is designed to penetrate and remain breathable rather than create a heavy surface film.

Expert buying guidanceChoose the right product with confidence.
Confirm the surface, finish, coverage, and application conditions before checkout.
Use Sealer Finder Calculate coverage Application guidance
Browse all professional surface-care products
Ultra Seal Eco Shield Dry Look Penetrating Concrete Sealer
Professional product profile
Ultra Seal Eco Shield is a penetrating concrete sealer for projects that need water repellency and mineral-surface protection without a glossy film. It is designed for concrete, masonry, natural stone, and compatible porous surfaces.
Selection standardSurface + finish + applicationConfirm all three before ordering.
Real-world application
FinishDry / natural look
SystemWater-based penetrating sealer and densifier
Best forConcrete, pavers, natural stone, masonry, and compatible porous surfaces
ApplicationSprayer, roller, or brush after moisture and absorption checks
Natural-look protection
Product performance overview
Penetrating protection is chosen when the goal is to reduce water and contaminant absorption without creating a glossy surface film. Porosity, absorption rate, moisture, prior treatments, and the material itself determine whether the product can penetrate and perform as intended.
Best matched when
The surface is porous and absorbent, a natural appearance is preferred, and a test area confirms even penetration without residue or unwanted color change.
Key advantages
What this product is designed to deliver
- Penetrating protection without a heavy gloss
- Breathable water-repellent treatment
- Helps resist moisture, salts, and freeze-thaw stress
- Natural-looking finish for porous mineral substrates
Recommended uses
Where it performs best
Concrete patios, walls, foundations, pavers, natural stone, and other surfaces where a natural appearance is preferred.
Coverage planning
Measure before ordering
Coverage depends on porosity and absorption. Use the Coverage Calculator and perform a moisture test before application.
Open the Coverage Calculator
Job planning
Build the application around product requirements
Identify the substrate, remove soil and residue, allow the surface to reach the required moisture condition, verify absorption, calculate material from tested coverage, and remove excess product exactly as directed.
Four-stage process
Application overview
1. Remove dirt, wax, mildew, oil, loose material, and old incompatible coatings.
2. Verify the substrate is absorbent and check for trapped moisture before application.
3. Apply evenly and avoid puddles, runs, or unabsorbed material.
4. Allow the product to cure and keep the surface protected during the initial cure period.
Technical noteSurface compatibility, weather, moisture, dilution, mixing, dwell time, and cure requirements vary by product. Read the current label and SDS, test a small area, and follow the product-specific technical directions before full application.
Product questions
Frequently asked questions

Does Eco Shield create a wet look?
No. Eco Shield is positioned as a dry-look penetrating sealer that preserves a natural appearance.

Can I use it on freshly poured concrete?
The current product information includes freshly poured concrete after it has set for the required period. Follow the current label and verify moisture conditions.

Why is a moisture test important?
Trapped moisture can interfere with absorption, curing, and final performance. Test before sealing and correct moisture problems first.

Expert buying guidanceChoose the right product with confidence.
Confirm the surface, finish, coverage, and application conditions before checkout.
Use Sealer Finder Calculate coverage Application guidance
Browse all professional surface-care products
MAGIC: Water Repellent & Protector
Professional product profile
MAGIC is a deep-penetrating siloxane water repellent that helps protect compatible brick, concrete, grout, travertine, marble, granite, and other stone surfaces while keeping the original appearance visible.
Selection standardSurface + finish + applicationConfirm all three before ordering.
Real-world application
FinishInvisible / natural look
SystemPenetrating siloxane water repellent
Best forBrick, brick pavers, concrete, grout, travertine, marble, granite, clay tile, and compatible stone
ApplicationApply evenly to a clean, absorbent surface and remove excess material
Natural-look protection
Product performance overview
Penetrating protection is chosen when the goal is to reduce water and contaminant absorption without creating a glossy surface film. Porosity, absorption rate, moisture, prior treatments, and the material itself determine whether the product can penetrate and perform as intended.
Best matched when
The surface is porous and absorbent, a natural appearance is preferred, and a test area confirms even penetration without residue or unwanted color change.
Key advantages
What this product is designed to deliver
- Penetrates pores and capillaries
- Vapor permeable treatment
- No visible surface film when properly applied
- Helps reduce water absorption and related staining or efflorescence
Recommended uses
Where it performs best
Natural-look water repellency for stone, masonry, pavers, concrete, grout, and clay tile.
Coverage planning
Measure before ordering
Coverage varies by absorption and porosity. Test first and use the Coverage Calculator as an ordering guide.
Open the Coverage Calculator
Job planning
Build the application around product requirements
Identify the substrate, remove soil and residue, allow the surface to reach the required moisture condition, verify absorption, calculate material from tested coverage, and remove excess product exactly as directed.
Four-stage process
Application overview
1. Clean the surface and allow it to reach the moisture condition required by the label.
2. Confirm the surface is absorbent and test for appearance and repellency.
3. Apply evenly and keep the surface uniformly wet during the recommended application window.
4. Remove excess and allow the treatment to cure before evaluating the result.
Technical noteSurface compatibility, weather, moisture, dilution, mixing, dwell time, and cure requirements vary by product. Read the current label and SDS, test a small area, and follow the product-specific technical directions before full application.
Product questions
Frequently asked questions

Will MAGIC change the appearance of my stone?
It is designed to leave a natural appearance with no visible film when properly applied, but every stone varies. Always test first.

Is MAGIC breathable?
The product information describes a vapor-permeable, penetrating water-repellent treatment.

Can it be used on travertine?
Travertine is listed among the recommended surfaces. Confirm the stone is clean, absorbent, and compatible before treating the full area.

Expert buying guidanceChoose the right product with confidence.
Confirm the surface, finish, coverage, and application conditions before checkout.
Use Sealer Finder Calculate coverage Application guidance
Browse all professional surface-care products
Ultra Seal Enhancing Impregnating Stone Sealer
Professional product profile
Ultra Seal Enhancing Impregnating Stone Sealer is a slow-drying, solvent-based acrylic treatment that penetrates and enhances the natural color of compatible stone, tile, brick, pavers, and cementitious surfaces.
Selection standardSurface + finish + applicationConfirm all three before ordering.
Real-world application
FinishColor-enhanced / natural-to-satin
SystemSolvent-based acrylic impregnating sealer
Best forTravertine, slate, marble, unglazed tile, quarry tile, brick, clay pavers, and cementitious surfaces
ApplicationRoller, brush, or sprayer with controlled wipe-off and drying time
Stone color enhancement
Product performance overview
Color-enhancing stone treatments are selected by mineral type, density, absorption, existing treatments, and the final appearance demonstrated by a test patch. A penetrating enhancer is not the same as a high-gloss coating, and results can vary across naturally inconsistent stone.
Best matched when
The stone is absorbent, deeper natural color is desired, and test patches in representative areas confirm a consistent appearance.
Key advantages
What this product is designed to deliver
- Deepens the natural color of compatible stone and tile
- Slow drying allows time for penetration
- Works on dense and porous cementitious surfaces
- Designed for natural-to-satin enhancement rather than a mirror gloss
Recommended uses
Where it performs best
Color restoration and penetrating protection where a richer appearance is desired without a heavy gloss.
Coverage planning
Measure before ordering
Porosity has a major effect. Current guidance is approximately 150–200 sq. ft. per gallon for a first coat on very porous surfaces; confirm the label for the selected size and substrate.
Open the Coverage Calculator
Job planning
Build the application around product requirements
Identify the stone, clean it with a compatible process, let it reach the required moisture condition, test multiple representative areas, estimate coverage from actual absorption, and remove excess before it dries on the surface.
Four-stage process
Application overview
1. Clean, dry, and test the surface for absorption and desired color.
2. Apply a controlled coat and allow it to penetrate without leaving puddles.
3. Remove excess material and watch edges, joints, and low spots during dry time.
4. Apply additional coats only when the label and test area support them.
Technical noteSurface compatibility, weather, moisture, dilution, mixing, dwell time, and cure requirements vary by product. Read the current label and SDS, test a small area, and follow the product-specific technical directions before full application.
Product questions
Frequently asked questions

Does this stone sealer create a glossy finish?
It is intended for color enhancement with a natural-to-satin appearance when properly applied, not a heavy mirror gloss.

Can I use it on travertine?
Travertine is among the recommended surfaces. Test first because absorption, color, and finish vary by stone.

Why is the product slow drying?
The slower dry time gives the impregnating treatment time to penetrate. Plan the work so the surface can remain undisturbed during curing.

Expert buying guidanceChoose the right product with confidence.
Confirm the surface, finish, coverage, and application conditions before checkout.
Use Sealer Finder Calculate coverage Application guidance
Browse all professional surface-care products
ULTRA SEAL – Classic Gloss Wet Look Paver Sealer
Professional product profile
ULTRA SEAL Classic Gloss is a two-component water-based urethane paver sealer that enhances color, stabilizes joint sand, and creates a durable wet-look barrier on properly prepared pavers and concrete.
Selection standardSurface + finish + applicationConfirm all three before ordering.
Real-world application
FinishClassic gloss / wet look
SystemTwo-component water-based urethane
Best forBrick pavers, concrete pavers, patios, driveways, walkways, and pool decks
ApplicationMix the kit as directed, then apply with the selected roller or sprayer
Wet-look protection
Product performance overview
Wet-look and high-gloss sealers should be selected by substrate porosity, the condition of any existing coating, joint condition, desired sheen, weather, and cure window. Film build and appearance depend on thin, controlled application over a properly prepared surface.
Best matched when
The surface is compatible, the desired result includes visible color enhancement, and the applicator can control moisture, coat thickness, and cure conditions.
Key advantages
What this product is designed to deliver
- Two-component urethane protection
- Deep color enhancement and classic gloss
- Helps lock joint sand in place
- Can work with a properly damp surface when the system directions allow it
- Low-odor, VOC-compliant product positioning in the current information
Recommended uses
Where it performs best
Wet-look color enhancement, joint-sand stabilization, and protective sealing for residential or commercial hardscape.
Coverage planning
Measure before ordering
Coverage depends on porosity, joint condition, and number of coats. Use the Coverage Calculator and order for the recommended application.
Open the Coverage Calculator
Job planning
Build the application around product requirements
Confirm the old coating and substrate are compatible, remove contaminants and failed material, repair joints as needed, measure the area, make a representative test patch, and apply only within the product-specific weather and recoat requirements.
Four-stage process
Application overview
1. Complete cleaning, joint-sand repair, and substrate preparation first.
2. Measure and mix the two components exactly as directed.
3. Apply controlled coats while monitoring puddles, lap marks, and changing weather.
4. Keep the surface protected through the full cure before returning it to service.
Technical noteSurface compatibility, weather, moisture, dilution, mixing, dwell time, and cure requirements vary by product. Read the current label and SDS, test a small area, and follow the product-specific technical directions before full application.
Product questions
Frequently asked questions

What makes ULTRA SEAL different from a 1K sealer?
ULTRA SEAL Classic Gloss is a two-component water-based urethane system. The components are combined immediately before application according to the kit directions.

Does it stabilize joint sand?
The product is designed to help lock properly installed joint sand in place. It does not replace correct joint preparation or a suitable sand selection.

Can I clean and seal the same day?
The current information describes damp-surface application. Same-day work still depends on cleaning, drainage, weather, substrate condition, and the label directions.

Expert buying guidanceChoose the right product with confidence.
Confirm the surface, finish, coverage, and application conditions before checkout.
Use Sealer Finder Calculate coverage Application guidance
Browse all professional surface-care products
APEX High Gloss Concrete Sealer
Professional product profile
APEX High Gloss Concrete Sealer is a waterborne, single-component acrylic/hybrid coating for concrete and compatible paver surfaces. It offers a straightforward alternative to traditional two-component epoxy-style finishes.
Selection standardSurface + finish + applicationConfirm all three before ordering.
Real-world application
FinishHigh gloss / clear protective film
SystemSingle-component waterborne acrylic/hybrid
Best forPrepared concrete, decorative concrete, and compatible paver surfaces
ApplicationRoller or sprayer after cleaning, profiling, and moisture checks
Protective coating system
Product performance overview
Floor and masonry coatings depend on substrate soundness, surface profile, moisture conditions, accurate proportioning, mixing quality, film thickness, recoat timing, and cure protection. Finish alone is not a reliable way to choose or apply a coating.
Best matched when
The substrate is sound and correctly profiled, moisture is within product limits, and the installer can control mixing, working time, film build, and cure conditions.
Key advantages
What this product is designed to deliver
- No two-part mixing
- Waterborne and low-odor positioning
- Designed to resist yellowing and discoloration
- Built-in UV inhibitor in the current product information
- Straightforward cleanup compared with traditional solvent systems
Recommended uses
Where it performs best
Decorative concrete, pavers, patios, walkways, driveways, and compatible floors where a clear gloss is desired.
Coverage planning
Measure before ordering
Coverage varies by substrate profile and coating build. Test first and use the product guidance for the project.
Open the Coverage Calculator
Job planning
Build the application around product requirements
Evaluate the substrate, repair defects, remove contaminants, create the required profile, confirm moisture conditions, stage tools and materials, mix exactly as directed, and protect the coating through its full cure window.
Four-stage process
Application overview
1. Clean, profile, and moisture-test the surface.
2. Confirm compatibility and desired gloss with a test area.
3. Apply a controlled coat without puddles, lap marks, or heavy buildup.
4. Protect the finish through the full cure and follow maintenance guidance.
Technical noteSurface compatibility, weather, moisture, dilution, mixing, dwell time, and cure requirements vary by product. Read the current label and SDS, test a small area, and follow the product-specific technical directions before full application.
Product questions
Frequently asked questions

Does APEX require mixing?
The current product information describes it as a single-component acrylic/hybrid, so no two-part mix is required.

Is it a high-gloss concrete sealer?
Yes. It is positioned as a high-gloss clear protective coating for compatible prepared concrete and paver surfaces.

Can it be used outdoors?
Outdoor use depends on the exact substrate, preparation, weather, and product directions. Test first and follow the current technical data.

Expert buying guidanceChoose the right product with confidence.
Confirm the surface, finish, coverage, and application conditions before checkout.
Use Sealer Finder Calculate coverage Application guidance
Browse all professional surface-care products

Paver Sealant

UltraGloss SX – High Gloss Urethane Sealer

Product performance overview

What this product is designed to deliver

Where it performs best

Measure before ordering

Build the application around product requirements

Application overview

Frequently asked questions

Ultra Seal Penetrating Natural Stone Sealer

Product performance overview

What this product is designed to deliver

Where it performs best

Measure before ordering

Build the application around product requirements

Application overview

Frequently asked questions

Ultra Seal Eco Shield Dry Look Penetrating Concrete Sealer

Product performance overview

What this product is designed to deliver

Where it performs best

Measure before ordering

Build the application around product requirements

Application overview

Frequently asked questions

MAGIC: Water Repellent & Protector

Product performance overview

What this product is designed to deliver

Where it performs best

Measure before ordering

Build the application around product requirements

Application overview

Frequently asked questions

Ultra Seal Enhancing Impregnating Stone Sealer

Product performance overview

What this product is designed to deliver

Where it performs best

Measure before ordering

Build the application around product requirements

Application overview

Frequently asked questions

ULTRA SEAL – Classic Gloss Wet Look Paver Sealer

Product performance overview

What this product is designed to deliver

Where it performs best

Measure before ordering

Build the application around product requirements

Application overview

Frequently asked questions

APEX High Gloss Concrete Sealer

Product performance overview

What this product is designed to deliver

Where it performs best

Measure before ordering

Build the application around product requirements

Application overview

Frequently asked questions