Sealer

F9 Double Eagle

For use on Concrete, Bricks, Pavers, Tile, Stone, Grout Masonry Hard Surfaces and most surfaces in general. Great for food grease, oils, dumpster pads, loading docks, gas stations, parking garages, tire marks and general cleaning of many surfaces.

DILUTION RATIOS

Very Heavily Soiled Surfaces: Straight

Heavily Soiled Surfaces: 1:1 to 5:1

Moderately Soiled Surfaces: 10:1

Lightly Soiled Surfaces: 20:1

CLEANING INSTRUCTIONS

Direct Application: Pump Sprayer, Electric or Air Diaphragm Spray System.

Dilution will depend on how dirty the area is. Product may be diluted 5:1 to 20:1. Spray on, dwell 2-15 minutes. Manually agitate heavy areas or use floor tool. Surface clean after. Hot water preferred, cold water ok.

Downstream Application: Use a downstream injection system capable of giving you the correct dilution rate for the circumstances. Spray on, dwell 2-15 minutes. Manually agitate heavy areas or use floor tool. Surface clean after. Hot water preferred, cold water ok.

X-Jet Application: Dilute product to give you the correct dilution rate for the circumstances. Spray on, dwell 2-15 minutes. Manually agitate heavy areas or use floor tool. Surface clean after. Hot water preferred, cold water ok.

Note: If areas are extremely soiled, use a 175 floor tool with extra-aggressive mal-grit to agitate.

HOW TO USE AS A NEUTRALIZER

General Neutralizing: 8:1. Spray on surface to be neutralized. Broom in if necessary. Rinse or surface clean. Make stronger to bring final pH of discharge up. Make weaker if you need to adjust final pH down. Always check wastewater to make sure final discharge pH is correct for City BMP’s.

F9 Efflorescence & Calcium Remover

Calcium and Efflorescence Remover is breakthrough in the restoration and cleaning industry. F9 Calcium and Efflorescence Remover is a user friendly, full 31.45% strength muriatic acid replacement. This product combines a buffered, pleasant smelling acid along with an excellent soaping capability to work better at lower concentrations. F9 Calcium and Efflorescence Remover gives the user the advantage of a full strength product while greatly reducing fuming and corrosion, thereby improving overall health and safety risk profile.

F9 Barc

Quantity of 1 Gallon Units. 1 Gallon of BARC concentrate makes up to 3 gallons of cleaner.

F9 BARC is for F9 Authorized Applicators, Contractors and Maintenance Department Use Only. By purchasing F9 products you are agreeing that you are an F9 Authorized Applicator, Contractor or Maintenance Department. Front 9 Restoration, Inc. is not responsible for improper application nor will we be held responsible for any damage caused by improper application of our products.

One Gallon of F9 BARC Makes 1.5 to 3 Gallons of Cleaner. Always Mix F9 with Only Clean Water Prior to Application.
One Gallon of F9 Concrete Rust Remover will cover 400-800′ of Concrete.
Check Out F9 University For Detailed Application Videos.

DO NOT USE ON GLASS

AGG Sealer Formula 888

SURFACES WHERE AGG 888 EXCELS:

  • Mexican Saltillo

  • Pavers

  • Brick

  • Exposed Aggregate

  • Rough Stone

  • Concrete Pavers

  • Concrete Driveways

SURFACE PREPARATION:

Always be sure the surface is clean, dry, and free from any dirt, grease, oil, wax, or other contaminants. Read the entire label before using. Use only as directed. Always test on a small piece of material or a small inconspicuous area to determine suitability. Ensure the area is well ventilated. Ideal surface temperature should be between 60°F and 80°F. Product works best when it is the first substance applied to the surface, insuring proper penetration.

COVERAGE:

For very porous surfaces: 1st coat: 75-150 sq. ft./gallon. 2nd coat 250-400 sq. ft./gallon. 3rd coat 500+ sq. ft./gallon.

For average density surfaces: 1st coat: 200-300 sq. ft./gallon. 2nd coat 400-500 sq. ft./gallon.

For very dense surfaces: 1000 sq. ft./gallon. Allow 24 hours between coats.

APPLICATION:

PAVERS: Apply with a solvent resistant paint roller having a 1/4 to 3/8-inch nap. Saturate paint roller and remove excess to prevent dripping. Roll sealer liberally, evenly, smoothly, and uniformly. Allow 12 hours to dry. One medium/heavy coat may be sufficient. Additional coats can be applied to increase gloss or even appearance.

MEXICAN SALTILLO TILE:

NEW INSTALLATIONS- BEFORE & AFTER GROUTING: Apply with a solvent resistant paint roller having a 1/4 to 3/8-inch nap. Saturate paint roller and remove excess to prevent dripping. Apply one medium/heavy coat before grouting after tiles have been laid in place and set firmly. Roll on sealer liberally, evenly, smoothly, and uniformly. Do not leave voids and puddles. Work in small areas at a time. Let the sealer dry 12-24 hours before grouting. Clean grout and let surface dry 3-4 days to make sure the grout joints are dry before applying a second coat of sealer. Allow second coat to dry a minimum of 12 hours before applying a third coat if necessary. Gloss will increase as additional coats are added.

RE-APPLICATION: Remove any floor finish on the surface, and clean thoroughly. Allow 12 hours to dry before sealing. Apply with a solvent resistant paint roller having a 1/4 to 3/8-inch nap. Saturate paint roller and remove excess to prevent dripping. Apply one light coat and allow 12 hours to dry. Additional coats can be added if necessary, to add gloss or even appearance. After the sealer is dry, Top Kote Floor Finish can be added to give the floor a glossy finish and protect the sealer.

WIRE CUT BRICK PAVERS: Before grouting, apply a medium coat of sealer with a paint roller having a ¼ inch nap to help protect the tiles from sticking grout. Roll on sealer liberally, evenly, smoothly, and uniformly. Do not leave voids and puddles. Work in small areas at a time. Let the sealer dry 8-24 hours before grouting. Clean grout and let surface dry thoroughly(2-3 days) before applying a second coat in order to seal grout joint.

EXPOSED AGGREGATE: Apply one heavy coat with a ½ to ¾ inch nap paint roller. Let dry. Usually one heavy coat applied properly is sufficient.

STONE: For best results apply with hair bristle paint brush

CLEANUP

Xylene or similar solvent can be used to clean tools.

STORAGE AND HANDLING

CAUTION: Highly flammable & combustible liquid and vapor. Do not handle until all safety precautions have been read and understood. Handling: Do not get in eyes, on skin, or on clothing. Do not breathe vapors or mists. Keep container closed and tightly sealed when not in use. Keep away from sources of ignition – No smoking. Take measures to prevent the buildup of electrostatic charge. Conditions for safe storage: Keep in tightly closed, properly labeled containers. Keep in a cool, well-ventilated place. Materials to avoid: Do not store with the following product types: Strong oxidizing agents, Explosives, Gases.

Rust Erase Pro – Professional Grade Stain & Rust Remover

Ultra Seal Ultimate Surface Prep

FOR CLEANING:

  • Brick Pavers
  • Irrigation Stains
  • Rust Stains
  • Limestone
  • Brownstone
  • Unpolished Marble
  • Precast
  • Exposed Aggregate
  • Concrete
  • Brick
  • Block
  • Terra Cotta
  • Vinyl
  • Metals
  • Wood
  • Synthetic Decking
  • Stucco
  • Sealer Cleaning
  • Unpolished Natural Stone
  • 10:1 Dilution – (can be downstreamed)

Do not allow to come in contact with glass.

Application: Dilute 1 part Ultimate Surface Prep with 10 parts water.  Apply and let dwell for two to three minutes before pressure washing surface. Rinse well.  Heavy staining might require additional applications.

Ultra Seal Penetrating Natural Stone Sealer

ADVANTAGES

  • Reduces water absorption into the substrate, thus reducing spalling due to freeze thaw and efflorescence, thereby increasing the life of the substrate.
  • Colorless and non-yellowing protection preserves the natural appearance of the substrate.
  • Penetrating & breathable
  • Water based and Environmentally Friendly
  • May be applied to damp surfaces
  • May be painted over
  • Inhibits mold and algae growth
  • Inhibits salt water infiltration

RECOMMENDED USES: For properly prepared, unsealed natural stone, concrete walls, foundations, pre-cast concrete, block, brick and most aggregate surfaces.

SURFACE PREPARATION: Substrate must be pressure washed and cleaned  prior to application of Penetrating Concrete Sealer and Damp Proofer. Surface should be cleaned and treated for organic growth and oil with CLEAR PINK STUFF prior to application. Efflorescence should be treated with CLEAN UP Efflorescence Remover.

APPLICATION INFORMATION: Apply with brush, roller, or pump sprayer. When spraying, use a fan or cone tip designed for water based coatings. Apply when surface and air temperatures are above 60° Fahrenheit and rising. Do not apply if the threat of rain exists within 12 hours.

  • Do not over apply or allow product to puddle.
  • Wet on Wet application – apply product until it begins to repel itself.
  • Wipe off excess.
  • Do not apply to a surface that was previously sealed with a film-forming or topical sealer
  • May be applied to damp surface, however, do not apply when standing water is present
  • May be used as a Moisture Vapor Barrier prior to applying an coating

Coverage: Coverage will depend on porosity of the substrate. Coverage averages up to 250 square feet per gallon depending on the porosity.

TERATONE 467

SURFACES WHERE TERATONE 467 EXCELS:

  • High Traffic Areas: TERATONE 467 provides a tough and durable barrier to protect high traffic areas from dirt, spills, and stains.

  • Very Porous Surfaces: Porous surfaces absorb stains very easily. TERATONE 467’s protective coating inhibits absorption by porous material.

  • Outdoor Surfaces: TERATONE 467 excels against the constant threats faced by outdoor surfaces. TERATONE 467 protects from the effects of weathering, rain, and UV damage.

SURFACE PREPARATION:

Always be sure the surface is clean, dry, and free from any dirt, grease, oil, wax, or other contaminants. Read the entire label before using. Use only as directed. Always test on a small piece of material or a small inconspicuous area to determine suitability. Ensure the area is well ventilated. Ideal surface temperature should be between 60°F and 80°F. Product works best when it is the first substance applied to the surface, insuring proper penetration.

APPLICATION:

For best results, apply TERATONE 467 with a short nap paint roller(1/4”- 1/2”). Spread in thin coats, evenly and uniformly, leaving no puddles. Allow 8-24 hours to dry before adding a second coat. May also be applied with spray applicator, natural fiber paint brush, roller, or lint free rag.

CLEANUP

Xylene or similar solvent can be used to clean tools.

Clean Up Efflorescence Remover

CLEAN UP Efflorescence Remover is a specially formulated, non-regulated liquid agent designed for use on brick, tile, and concrete surfaces. Clean Up quickly and effectively removes mortar smear, construction dirt, and efflorescence without damaging surrounding surfaces. is 100% Biodegradable, Non-Corrosive, Non-Regulated, and a Non-Skin Irritant.

Proper Shipping Name – Clean Up Efflorescence Remover
Non-Hazardous for Transport by Truck
DOT Hazard Class – Not Regulated
Packing Group – Not Regulated
ID# – None

Available in 1 Gallon Jugs

Clear Pink Stuff

Inhalation: Remove affected person to fresh air; get immediate medical attention with emphasis on hydrofluoric acid exposure. If breathing is difficult, supply oxygen. If breathing has stopped, begin artificial respiration.

Skin: Remove contaminated clothing while flushing affected area with drenching shower for 5 minutes. Launder contaminated clothing before reuse; seek immediate medical attention with emphasis on hydrofluoric acid exposure. Apply 2.5% Calcium Gluconate ointment to contacted area.

Eyes: Check for and remove contact lenses. Immediately flush eyes for 5 minutes in clear running water while holding eyelids open; seek immediate medical attention with emphasis on hydrofluoric acid exposure. Irrigate open eyelids with 500 to 1,000 cc’s of 1% Calcium Gluconate in saline solution.

Ingestion: Drink high amounts of calcium based antacid in water followed by milk or milk of magnesia; DO NOT induce vomiting; never give anything by to an unconscious person; seek immediate medical attention with emphasis on hydrofluoric acid exposure

Ultra Seal Eco Shield Dry Look Penetrating Concrete Sealer

SURFACE PREPARATION

For freshly poured concrete: Apply after concrete sets for at least 24 hours. Make sure no water puddles are present. Concrete may be slightly wet before applying.

For fully cured concrete: Remove all dirt, wax, dust, mildew, and loose or scaling material with a scraper, wire brush, or stiff bristle brush. Grease, wax, and oil should be removed by scrubbing with CLEAR PINK STUFF or a heavy duty detergent in warm water. Rinse thoroughly with clean water. Allow to dry. If using a pressure washer, do not use on a pressure setting above 1750 psi to avoid damaging the concrete. Remember, concrete acts like a sponge – pressure washing and general cleaning may trap residual moisture in the concrete. To check for trapped moisture, tape a 12”x12” piece of 3 mil plastic or aluminum foil tightly on all four edges to the surface. Remove it after 24 hours. If the floor side of the plastic or foil is damp, allow additional drying and repeat the test.

EFFLORESCENCE: A white, powdery, crystal-like deposit visible on the masonry surface, should be removed. CLEAN UP EFFLORESCENCE REMOVER or muriatic acid, used according to manufacturer’s directions, are effective efflorescence removal agents. All masonry surfaces are subject to occurrences of efflorescence. Properly prepared concrete should look and feel like medium grit sandpaper. If concrete remains smooth, repeat etching procedure. Test concrete porosity by sprinkling a few drops of water on to the surface in several areas. If the water is readily absorbed, you are ready to paint. If it beads or lays on the surface, additional cleaning and etching is needed. Rinse thoroughly with clean water and allow to dry for 24 hours.

NOTE: Rinse etching solutions thoroughly. Etching solutions allowed to dry on masonry surfaces prevent proper curing of ECO SHIELD DRY LOOK PENETRATING CONCRETE SEALER and may result in the ECO SHIELD DRY LOOK PENETRATING CONCRETE SEALER appearing milky when dry. Patch all holes and cracks with a masonry crack filler or a suitable cement-based patching compound. Be sure to smooth the patch evenly. Allow the patched area to dry thoroughly.

APPLICATION

Apply only when air and surface temperature is above 50° F and humidity below 70%. Do not apply if raining or if it will rain within 48 hours of application. ECO SHIELD DRY LOOK PENETRATING CONCRETE SEALER appears milky in the pail but dries clear. Apply by brush, roller, spray, or squeegee. Spread evenly – do not allow puddles or a heavy surface film to
occur. Apply one coat using thin even strokes. Extremely porous surfaces may require a second coat. Allow 6 hours drying time between coats. Additional coats will cause surface to be
slippery when wet. On light-colored surfaces, some darkening may take place; test in an inconspicuous area to be sure darkening does not occur. May be applied to surfaces previously coated with a similar treatment. For best results, test a small area for proper adhesion prior to coating entire surface.

THINNING
Due to variations in porosity, when applied over flagstone, slate, terrazzo, dense smooth or light colored concrete, thin with clean, moderately warm water 10%—20% to minimize sheen.

In addition, light colored concrete may darken unevenly due to variations in porosity. Test on a small area to see final effect.

MAGIC: Water Repellent & Protector

MAGIC is a deep penetrating, siloxane water repellant which produces a transparent protective barrier across the surface of a stone. MAGIC fills the pores and capillaries of the stone, and forms an invisible, vapor permeable membrane across the surface. This coating repels moisture from the surface while allowing the stone to breathe. MAGIC has no visible film, and leaves surfaces looking natural with no change in appearance.

MAGIC inhibits mold, mildew, and efflorescence, as well as damage caused by the constant absorption and evaporation of water from the stone. MAGIC penetrates immediately, deeply, and effectively, providing a long lasting protective barrier.

For use on Brick, Brick Pavers, Unglazed Ceramic Tile, Clay Tiles, European Clay Pavers, Concrete, Grout Joints, Saltillo Tiles, Travertine, Marble, Granite, or any stone surface when a natural look is desired. MAGIC serves as an excellent grout release. For interior or exterior use.

Ultra Seal Enhancing Impregnating Stone Sealer

Enhancing Impregnating Natural Stone Sealer is a color enhancing, slow drying, deep penetrating, solvent based acrylic sealer for interior or exterior use. Ultra Seal Enhancing Impregnating Natural Stone Sealer's slow drying nature allows it to penetrate deep before setting. Will enhance the natural colors of most surfaces. Very effective at sealing and protecting dense and smooth surfaces such as quarry tile, ceramic tile, slate, unfinished marble, terrazzo, travertine, smooth cement, and all other cementitious materials. Recommended for use on unglazed surfaces when NO gloss or a SATIN finish with color enhancement is desired.

RECOMMENDED SURFACES
• Travertine
• Brazilian & Spanish Tile
• Unglazed Tile
• Marble
• Stone, Brick, & Clay Pavers
• Exposed Aggregates
• Quarry Tile

COVERAGE
For very porous surfaces: 1st coat: 150-200 sq. ft./gallon.
2nd coat 300-400 sq. ft./gallon.

For average density surfaces: 1st coat: 250-300+ sq.ft./gallon.
2nd coat 400+ sq. ft./gallon.
For very dense surfaces: 1.5x avg. density coverage Generally, the sealer will go twice as far on the 2nd coat as it did on the 1st coat.

Allow 24 hours between coats.

SURFACE PREPARATION

Always be sure surface is clean, dry, and free from any dirt, grease, oil, wax, or other contaminant. Read the entire label before using. Use only as directed. Always test on a small piece of material or a small inconspicuous area to determine suitability. Ensure the area is well ventilated. Ideal surface temperature should be between 60°F and 80°F. Product works best when it is the first substance applied to the surface, insuring proper penetration.

APPLICATION

Ultra Seal Enhancing Impregnating Natural Stone Sealer may be applied with spray applicator, brush, roller, or lint free rag. Spread evenly and uniformly- cover entire area, leaving no puddles. Avoid puddles by wiping up excess. Allow 24 hours between coats to ensure it has dried completely.
No buffing required.

SMOOTH SURFACES: apply Ultra Seal Enhancing Impregnating Natural Stone Sealer with a lint free cloth or short nap roller.

ROUGH SURFACES: apply with a 1⁄2 to 3⁄4 inch nap paint roller or paint brush.

VOC: 1.09 lb./gallon, 130.66 g/L

STORAGE AND HANDLING

CAUTION: Highly flammable & combustible liquid and vapor. Do not handle until all safety precautions have been read and
understood.

Handling: Do not get in eyes, on skin, or on clothing. Do not breathe vapors or mists. Keep container closed and tightly sealed when not in use. Keep away from sources of ignition – No
smoking. Take measures to prevent the buildup of electrostatic charge.

Conditions for safe storage: Keep in tightly closed, properly labeled containers. Keep in a cool, well-ventilated place.
Materials to avoid: Do not store with the following product types: Strong oxidizing agents, Explosives, Gases.

FIRST AID MEASURES

Eye Contact: Flush eyes with water. Seek medical attention if irritation persists.

Skin Contact: Remove contaminated clothing. Wash with soap and water. Seek medical attention if irritation persists.
Inhalation: If inhaled, remove to fresh air. If respiratory irritation, dizziness, nausea, or unconsciousness occurs, seek immediate medical assistance. In case of unconsciousness place patient stably in side position for transportation.

Ingestion: Do NOT induce vomiting unless directed to do so by medical personnel. Never give anything by mouth to an unconscious person. Rinse mouth with water. Seek medical attention if symptoms appear.

Water Based Epoxy Concrete floor and Concrete Block Wall Waterproofer

Typical Applications:
Retail and Commercial Flooring
Concrete block walls.
Garage and Showroom Floors
High-Traffic Interior Applications

Approved Topcoats:
Solvent or Water-Based Urethane and 100 solids .
Also approved for wood, concrete and laminate countertops

Surface Prep & Priming:
Grind concrete floors to CSP-3, vacuum dust, wipe with
Denatured alcohol.

Mixing:
Three parts A to 1-part B by volume.
Mixing full kits Add premeasured Part B to Part A Mix for
2 minutes with mechanical mixing. Wearing spike shoes
immediately pour mixed material on the floor and
spread using a flat squeegee or for smaller projects can
be dipped and rolled using 3/8” epoxy roller.

Metallic Applications:
Excellent primer for metallic applications. Premixed
black primer kits available.

Coverage:

1 gallon will cover approximately
Porous Concrete block 200-250 sq.ft./gal.
Receiver coat for vinyl chips 200-250 sq.ft./gal Clear

Finish Coat 250-300 sq.ft./gal.

Best if applied at temperatures between
55-90 degrees Fahrenheit.

Broadcasting Vinyl Chips:
Apply pigmented epoxy basecoat at 200 sq.ft. per gallon
Vinyl flake on 250 sq.ft.

Light 1lb. Heavy 4lbs. Full 25lbs.

After epoxy is spread and back rolled divide chips in
equal portions then throw vinyl chips upwards let them
drop in the wet epoxy. Let cure 24hrs. Then scrape and
vacuum up loose flakes. After scraping and vacuuming
several times. Apply coat of Polyaspartic Clear
or using a magic trowel pull seal coat across the flake at
180 sq. ft per gallon. A Water-Based Two Component Urethane is
also an excellent choice for low odor applications.

Dry-time & Recoat:

Tack free/foot traffic: 12 hrs. Recoat 24 hrs.
Heavy foot traffic 48 hrs. Vehicular Traffic 3 days.
Lightly sand the surface and wipe down with denatured
alcohol or acetone before applying additional coats or
finish coats.

Exterior Applications:

Unless installed as a primer with pigmented Urethane
Topcoats. Not recommended as clear epoxy will amber.

Handling, Storage, Disposal & Clean-up:

  • May irritate eyes wear gloves
  • Store in clean dry area do not freeze
  • Dispose in accordance with all state local and federal
    laws
  • Clean-up tools and equipment with water
  • Regulatory
  • Less than 250 grams/liter
  • Meets all VOC categories in US / except SCAQMD

Warranty:

Material only if proven defective, no labor

Melt Away Paint Stripper – Fast, Effective Coating Remover

 

  • Removes multiple layers in one application.
  • Effective on , pint, acrylic sealers, epoxies & enamels
  • Strong emulsifier package lifts sealer in 15-20 minutes
  • Water soluble clean rinse technology
  • Sprayable VOC compliant
  • Methylene chloride and caustic free
  • Non Flammable
  • Dual action – lifts and emulsifies the coating
  • Bio-degradable and Environmentally Friendly
  • Ships DOT Non-Flammable, Non-Hazardous to all 50 states including California

Warrantied against material free of defects.  Not warrantied against labor.

Application Instructions:

Pour contents into a pump-up sprayer system, cover and or dampen with water any grass, plants, or flowers they may encounter with overspray, then uniformly apply a flood coat of Melt Away . Hold sprayer tip 12” from the surface while spraying and let dwell for 15-20 minutes (excessive layers may need longer dwell times or reapplication) until sealer and other coatings start to turn grayish or shows signs of peeling.

Using a plastic putty knife, you should be able to scrape the coating from the substrate. At this point it is ready to rinse utilizing a pressure washer with a turbo tip. The use of a fan tip as zero tip is not recommended as it will leave etch the substrate. Melt Away Paint Stripper and paver sealer remover can also be applied using a ½ nap roller as well.

Distributed by , LLC

ULTRA SEAL – Classic Gloss Wet Look Paver Sealer

ULTRA – Wet Look is a two-component urethane which provides deep color enhancement and joint stabilization by locking the sand in-between the joints in place, forms a long-lasting protective barrier on the surface of the pavers or concrete, protecting them from the natural elements and the suns harmful UV rays. Not only is it user friendly, but it produces a consistent finish that wears evenly over time.

All of products are environmentally friendly, bio-degradable, will not harm vegetation, pet friendly, and are commercial quality – formulated with the contractor in mind. All products are VOC's compliant and can be used in all 50 states.

Click here for more before and after photos.

 

Semi Transparent Color Additives, Dyes, Stains and Tints

and translucent tints are a great way to restore color back to faded pavers, tint and stain concrete. They are safe non toxic, colorfast, and can be blended together to make custom colors.

The intensity of the color will vary by the amount of tint added.  Add a 1/2 oz of pigment to achieve a more translucent finish, or add up to 1oz per 5 gallons of diluted water based sealer for more of a staining effect.

The amount of color needed will vary depending on the product used and color desired. For lighter colors, it may take more tint, and darker colors may take less tint, depending on the application.

Do not add too much tint as it can cause color float or streaking, especially on darker colors.  Lighter colors may require more tint.

Solvent based color additives and dyes are available. Please contact us for availability.

Seal RX Enhance

SEAL Rx ENHANCE

Seal RX Enhance Stone Sealer is a heavy duty, solvent based, silane-siloxane designed to enhance color, impart water repellency and stain resistance to a wide variety of natural stone, concrete and aggregate surfaces.  The silanes react chemically and bond with the substrate to form an insoluble water-resistant treatment within 24-72 hours after application.

__________________________________________________________________________________________

 

RECOMMENDED USES:

For properly prepared, unsealed natural stone, concrete walls, foundations, pre-cast concrete, block, brick and most aggregate surfaces.

 

SURFACE PREPARATION:

Dirt, grease, grime and any foreign material must be removed before application of SEAL Rx ENHANCE.  Treat surface for mildew.  Oil and grease should be scrubbed with a solution of TSP and water.

 

APPLICATION INFORMATION:  

Apply with brush, roller, airless sprayer or pump sprayer.  When spraying, use a tip designed for gloss coatings.  Apply when surface and air temperatures are above 32 Deg. F and rising.  Do not apply if the threat of rain exists.  Do not over apply or allow product to puddle.

 

  • Always apply a test sample to insure compatibility
  • Do not apply to a surface that was previously treated with another product
  • Take care to cover nearby vegetation, glass, plastic and metals. Seal RX 580 may damage them.
  • May be applied to damp surface, however, do not apply when standing water is present

 

SEAL Rx ENHANCE requires different application methods for smooth and porous/rough surfaces.

 

Smooth surfaces:

  1. Apply with brush, roller or spray
  2. Allow to sit for 30-45 minutes
  3. Wipe off excess material with a t-shirt type material. The excess should be removed similar to removing wax from a car.

 

Porous/Rough surfaces: No wiping is necessary as long as product penetrated and no puddles or excess material is visible.

 

 

RECOMMENDED THINNER:

SEAL Rx ENHANCE does not require thinning and should be used as is, directly from the container.

 

BENEFITS:

 

  • Enhances color of substrate.
  • Reduces water absorption into the substrate, thus reducing spalling due to freeze thaw and efflorescence, thereby increasing the life of the substrate.
  • Resists staining
  • Colorless and non-yellowing protection preserves the appearance of the substrate.
  • Penetrating & breathable
  • Low VOC
  • May be applied to damp surfaces
  • UV Resistant
  • Reduces mildew growth on surface

 

 

TECHNICAL DATA:

Finish: Enhanced look                                                          

Pigment Type:  None

Solvent Type: Solvent

Density:  8.50 lbs./Gal.

Viscosity @ 75 deg. F (24 deg. C):  Waterlike

Coating VOC: <50 g/l

 

Clean Up: Clean up drips and spills immediately using any type of solvent.  Clean tools and equipment with any type of solvent.

 

Coverage (Theoretical): Coverage will depend on porosity and contour of the surface being coated.  Coverage typically averages 600-800 square feet per gallon.

 

Storage:  After use, make sure to seal lid tightly.  SEAL Rx ENHANCE will gel if left open.

 

Environmental & Safety Information:

Improper handling or use may be hazardous.  Recommended safety precautions for storage, handling and application must be observed.

 

DANGER: 

COMBUSTIBLE!  KEEP OUT OF REACH OF CHILDREN!

Contains flammable solvents.  Causes eye burns.  Vapor is harmful.  May cause allergic skin reaction.  Do not get in eyes, on skin or on clothing.  Wear eye and skin protective equipment when handling.  Wear appropriate, properly fitted respirator (NIOSH.MSHA approved) during and after application unless air monitoring demonstrates vapor/mist levels are below applicable levels.  Follow respirator manufacturer’s recommendations for use.  Keep containers closed when not in use.

First Aid:  In case of eye contact, flush eyes immediately with plenty of fresh water for at least 15 minutes.  Call a physician.  If inhaled, remove to fresh air.  If not breathing, give artificial respiration, preferably mouth to mouth and seek immediate medical assistance.  In case of skin contact, wash immediately with soap and fresh water.  Remove contaminated clothing and launder before use.  Discard shoes if material has penetrated inside surface.

Notice:  Reports have associated repeated and prolonged occupational overexposure to solvent with permanent brain and nervous system damage.  Intentional misuse by deliberately concentrating and inhaling the contents may be harmful or fatal.

 

WARNING! If you scrape, sand or remove old paint, you may release lead dust.  LEAD IS TOXIC.  EXPOSURE CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN.  PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE.  Wear an NIOSH-approved respirator to control lead exposure.  Carefully clean up with a HEPA vacuum and a wet mop.  Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

 

Technical data contained herein is true and accurate at the date of issue, but is subject to change without notice.  An Inseco representative should be contacted with any questions concerning product information or application procedures.  Our products conform to Inseco quality standards, but no other warranty is expressed or implied.  Liability, if any, is limited to the replacement of product or purchase price.

Paver Seal RX – 5 Gallon

Paver Seal Rx is a high-performance, water paver based that provides protection, deep color enhancement, joint stabilization and durability for concrete pavers. The penetrating technology of the product seals up the pores in porous materials such as concrete to build a clear coating around it providing stain resistance. With Paver Seal Rx paver sealant protecting the pavers, they will shine longer and resist damage from foot traffic or vehicular traffic better than ever before! In addition to these benefits, Paver Seal Rx also protects against mildew growth and degradation from UV rays which may discolor otherwise beautiful surfaces. To know more about this incredible sealant with many properties call us at 813-308-9202 today!

Smooth, wet surfaces are dominated by water molecules that attach themselves to the surface of the material with hydrophilic properties. Paver Seal Rx is a powerful sealer with hydrophobic properties which provides protective coating for porous materials like concrete pavers. With this deep penetrating technology, it does two important things: first seals up the pores in your paver's surface (providing protection) and second-coats them to provide long lasting color enhancement.

Not only will you be left with beautifully preserved pavers, but ones that will withstand foot traffic and vehicular traffic on them better than ever before! Say goodbye to dirt covered surfaces and welcome fresher looking pavers. This environmentally safe compound helps preserve against mildew growth as well as deterioration from uv rays and includes 3 year warranty!

RECOMMENDED USES:

For properly prepared concrete and brick pavers, slate, Saltillo tiles and clay roof tiles.

SURFACE PREPARATION:

Dirt, grease, grime and any foreign material must be removed before application of new coating. Treat surface
for mildew. Oil and grease should be scrubbed with a solution of TSP and water.

Contact a Paver Sealer Store representative at 619-658-5241 representative for detailed surface preparation specifications.

Do not apply to painted surfaces.

APPLICATION INFORMATION:

Mix product thoroughly and apply with brush, roller or airless sprayer. When spraying, use a tip designed for
gloss coatings. Apply when surface and air temperatures are above 50 Deg. F. Do not apply if the threat of rain
exists or if there is any puddling of water on the surface prior to Paver Seal RX curing. Cover and protect all
vegetation and surrounding areas not being sealed. Do not over apply, soak the substrate or allow product to
puddle. Two thin coats are recommended for best performance.

RECOMMENDED THINNER:

Paver Seal RX does not require thinning and should be used as is, directly from the container.

Paver Seal RX – 1 Gallon

Paver Seal Rx is a high-performance, water based sealer that provides protection, deep color enhancement, joint stabilization and durability for concrete pavers. The penetrating technology of the product seals up the pores in porous materials such as concrete to build a clear coating around it providing stain resistance. With Paver Seal Rx protecting the pavers, they will shine longer and resist damage from foot traffic or vehicular traffic better than ever before! In addition to these benefits, Paver Seal Rx also protects against mildew growth and degradation from UV rays which may discolor otherwise beautiful surfaces. To know more about this incredible sealant with many properties call us at 813-308-9202 today!

Smooth, wet surfaces are dominated by water molecules that attach themselves to the surface of the material with hydrophilic properties. Paver Seal Rx is a powerful sealer with hydrophobic properties which provides protective coating for porous materials like concrete pavers. With this deep penetrating technology, it does two important things: first seals up the pores in your paver's surface (providing protection) and second- coats them to provide long lasting color enhancement. Not only will you be left with beautifully preserved pavers, but ones that will withstand foot traffic and vehicular traffic on them better than ever before! Say goodbye to dirt covered surfaces and welcome fresher looking pavers. This environmentally safe compound helps preserve against mildew growth as well as deterioration from uv rays.

  • Available in 5 Gallon pails as well!
  • RECOMMENDED USES:
  • For properly prepared concrete and brick pavers, slate, Saltillo tiles and clay roof tiles.
  • SURFACE PREPARATION:
  • Dirt, grease, grime and any foreign material must be removed before application of new coating. Treat surface
    for mildew. Oil and grease should be scrubbed with a solution of TSP and water. Contact a Store representative at 813-308-9202
    representative for detailed surface preparation specifications.
    Do not apply to painted surfaces.
  • APPLICATION INFORMATION:
  • Mix product thoroughly and apply with brush, roller or airless sprayer. When spraying, use a tip designed for
    gloss coatings. Apply when surface and air temperatures are above 50 Deg. F. Do not apply if the threat of rain
    exists or if there is any puddling of water on the surface prior to Paver Seal RX curing. Cover and protect all
    vegetation and surrounding areas not being sealed. Do not over apply, soak the substrate or allow product to
    Two thin coats are recommended for best performance.
  • RECOMMENDED THINNER:
  • Paver Seal RX does not require thinning and should be used as is, directly from the container.